If the length of a clock's pendulum is increased by 1.600% exactly at noon, the clock will read 24.000 hours later at approximately 11:54:26.64.
This calculation assumes the pendulum has kept perfect time before the change.
To calculate the time the clock will read 24 hours later, we need to consider the change in the length of the pendulum. Increasing the length of the pendulum by 1.600% means the new length is 1.016 times the original length.
The time period of a pendulum is directly proportional to the square root of its length. Therefore, if the length increases by a factor of 1.016, the time period will increase by the square root of 1.016.
The square root of 1.016 is approximately 1.007976, which represents the factor by which the time period of the pendulum has increased.
Since the clock was adjusted exactly at noon, 24 hours later at noon, the pendulum would complete one full cycle. However, due to the increased time period, it will take slightly longer than 24 hours for the pendulum to complete a cycle.
To calculate the exact time, we can multiply 24 hours by the factor 1.007976. The result is approximately 24.19144 hours.
Converting this to minutes and seconds, we have 0.19144 hours * 60 minutes/hour = 11.4864 minutes. Converting the minutes to seconds gives us 11.4864 minutes * 60 seconds/minute = 689.184 seconds.
Therefore, the clock will read 24.000 hours later at approximately 11:54:26.64 (HH:MM:SS) with a precision of five digits.
To learn more about, length:-
brainly.com/question/31748974
#SPJ11
A block of mass 1.30 kg is placed on a frictionless floor and initially pushed northward, whereupon it begins sliding with a constant speed of 5.12 m/s. It eventually collides with a second, stationary block, of mass 4.82 kg, head-on, and rebounds back to the south. The collision is 100% elastic. What will be the speeds of the 1.30-kg and 4.82-kg blocks, respectively, after this collision?
2.05 m/s and 2.56 m/s
1.18 m/s and 2.75 m/s
2.94 m/s and 2.18 m/s
2.18 m/s and 2.94 m/s
To solve this problem, we can use the principle of conservation of momentum and the principle of conservation of kinetic energy.
Before the collision, the total momentum of the system is the sum of the momenta of the two blocks. After the collision, the total momentum remains the same.
Let's denote the initial velocity of the 1.30 kg block as v1i and the initial velocity of the 4.82 kg block as v2i. Since the 1.30 kg block is initially pushed northward, its velocity is positive, while the 4.82 kg block is stationary, so its initial velocity is 0.
Using the conservation of momentum:
(m1 × v1i) + (m2 × v2i) = (m1 × v1f) + (m2 × v2f)
Since the collision is elastic, the total kinetic energy before and after the collision remains the same. The kinetic energy equation can be written as:
0.5 × m1 × (v1i)^2 + 0.5 × m2 × (v2i)^2 = 0.5 × m1 × (v1f)^2 + 0.5 × m2 × (v2f)^2
We can solve these two equations simultaneously to find the final velocities (v1f and v2f) of the blocks after the collision.
Substituting the given masses (m1 = 1.30 kg and m2 = 4.82 kg) and initial velocity values into the equations, we find that the speeds of the 1.30 kg and 4.82 kg blocks after the collision are approximately 2.18 m/s and 2.94 m/s, respectively. Therefore, the correct answer is 2.18 m/s and 2.94 m/s.
To know more about conservation of momentum , please visit
https://brainly.com/question/24989124
#SPJ11
A projectile is projected from the origin with a velocity of 45.0 m/s at an angle of 30.0 degrees above the horizontal. What is the time it takes for the projectile to hit the ground?
The time it takes the projectile to hit the ground is 4.59 s.
What is time of flight?The time taken by the projectile to complete its trajectory is called time of flight.
To calculate the time of flight of the projectile to hit the ground,we used the formula below
Formula:
T = 2usin∅/g.................. Equation 1Where:
T = Time of flight of the projectile∅ = Angle of the projectileg = Acceleration due to gravityu = Intial velocityFrom the question,
Given:
u = 45 m/s∅ = 30°g = 9.8 m/s²Substitute these values into equation 1
T = 2(45×sin30°)/9.8T = 4.59 sLearn more about time of flight here: https://brainly.com/question/30438077
#SPJ4
The time it takes for the projectile to hit the ground is 4.59 seconds.
A projectile is projected from the origin with a velocity of 45.0 m/s at an angle of 30.0 degrees above the horizontal.
The horizontal and vertical motions of a projectile are independent of one another. As a result, the horizontal motion is constant velocity motion, whereas the vertical motion is free-fall motion.
Let's calculate the time it takes for the projectile to hit the ground:
First, we will calculate the time it takes for the projectile to reach the maximum height. Using the formula:v_y = v_iy + a_ytFinal velocity = 0 (since the projectile stops at the top)
v_iy = 45 sin 30° = 22.5 m/st = ?a_y = - 9.8 m/s² (negative acceleration since it is directed downwards) 0 = 22.5 - 9.8tt = 22.5 / 9.8t = 2.3 s
The time taken for the projectile to reach its highest point is 2.3 s.
Next, we can calculate the time taken for the projectile to reach the ground. Using the formula:y = v_iyt + (1/2) a_yt²y = 0 (since the projectile hits the ground)
v_iy = 22.5 m/s (from above)t = ?a_y = - 9.8 m/s² (negative since it is directed downwards) 0 = 22.5t - 4.9t²t(4.9t - 22.5) = 0t = 0 s (initially)t = 4.59 s (when the projectile hits the ground)
Learn more about projectile
https://brainly.com/question/28043302
#SPJ11
Explain it pleaseTwo particles of charge Q are located inside a box. One is at the box center while the other is halfway to one of the corners. Determine the electric flux through the box.
Answer: charge enclosed over epsilon not gives
The electric flux through the box is determined by the charge enclosed within the box divided by the permittivity of free space (ε₀). In this scenario, we have two particles of charge Q, with one located at the center of the box and the other halfway to one of the corners.
Since the charge at the center of the box is equidistant from all sides, it will produce an equal flux through each face of the box. On the other hand, the charge halfway to one of the corners will only contribute to the flux through one face of the box.
Therefore, the total electric flux through the box is given by the charge enclosed, which is the sum of the charges of both particles (2Q), divided by the permittivity of free space (ε₀). Mathematically, it can be expressed as:
Electric Flux = (2Q) / ε₀.
This equation signifies that the electric flux through the box is directly proportional to the total charge enclosed within it. The permittivity of free space (ε₀) is a constant that relates to the ability of the electric field to propagate through a vacuum.
To learn more about charge click here brainly.com/question/13871705
#SPJ11
Question 7 The ideal efficiency for a heat engine operating between temperatures of 2950 K and 318 Kis O a 50% b. 11% Oc 89% d 25% e zero
The ideal efficiency for a heat engine operating between temperatures of 2950 K and 318 Kis O ais approximately 0.0733 or 7.33% answer is: b)7%
The ideal efficiency for a heat engine operating between two temperatures can be calculated using the Carnot efficiency formula:
Efficiency = 1 - (Tc/Th)
where Tc is the absolute temperature of the cold reservoir and Th is the absolute temperature of the hot reservoir.
Given:
Temperature of the cold reservoir, Tc = 295 K
Temperature of the hot reservoir, Th = 318 K
Calculating the efficiency:
Efficiency = 1 - (Tc/Th)
Efficiency = 1 - (295/318)
Efficiency = 1 - 0.9267
Efficiency = 0.0733
The efficiency is approximately 0.0733 or 7.33%.
Therefore, the correct answer is:
b) 7%
To learn more about heat engine click here:
brainly.com/question/32897791
#SPJ11
Find out the positive, negative and zero phase sequence components of the following three phase unbalanced voltage vectors. Va-10230°V. Vb-302-60° V and Vc= 152145°
The positive, negative, and zero phase sequence components of the three-phase unbalanced voltage vectors were determined using phasor representation and sequence component transformation equations. V₁ represents the positive sequence, V₂ represents the negative sequence, and V₀ represents the zero sequence component. Complex number calculations were involved in obtaining these components.
To find the positive, negative, and zero phase sequence components of the given three-phase unbalanced voltage vectors, we need to convert the given vectors into phasor form and apply the appropriate sequence component transformation equations.
Let's denote the positive sequence component as V₁, negative sequence component as V₂, and zero sequence component as V₀.
Vₐ = 102∠30° V
Vb = 302∠-60° V
Vc = 152∠145° V
Converting the given vectors into phasor form:
Vₐ = 102∠30° V
Vb = 302∠-60° V
Vc = 152∠145° V
Next, we apply the sequence component transformation equations:
Positive sequence component:
V₁ = (Vₐ + aVb + a²Vc) / 3
= (102∠30° + a(302∠-60°) + a²(152∠145°)) / 3
Negative sequence component:
V₂ = (Vₐ + a²Vb + aVc) / 3
= (102∠30° + a²(302∠-60°) + a(152∠145°)) / 3
Zero sequence component:
V₀ = (Vₐ + Vb + Vc) / 3
= (102∠30° + 302∠-60° + 152∠145°) / 3
Using the values of 'a':
[tex]a = e^(j120°)\\a² = e^(j240°)[/tex]
Now, we can substitute the values and calculate the phase sequence components.
Please note that the calculations involve complex numbers and trigonometric operations, which are best represented in mathematical notation or using mathematical software.
To know more about voltage refer to-
https://brainly.com/question/32002804
#SPJ11
2. A shell is fired from a cliff horizontally with initial velocity of 800 m/s at a target on the ground 150 m below. How far away is the target? ( 2 pts) 3. You are standing 50 feet from a building and throw a ball through a window that is 26 feet above the ground. Your release point is 6 feet off of the ground (hint: you are only concerned with Δ y). You throw the ball at 30ft/sec. At what angle from the horizontal should you throw the ball? (hint: this is your launch angle) (2pts)
Horizontal displacement = 4008 meters
The launch angle should be approximately 20.5°
To find how far away the target is, the horizontal displacement of the shell needs to be found.
This can be done using the formula:
horizontal displacement = initial horizontal velocity x time
The time taken for the shell to reach the ground can be found using the formula:
vertical displacement = initial vertical velocity x time + 0.5 x acceleration x time^2
Since the shell is fired horizontally, its initial vertical velocity is 0. The acceleration due to gravity is 9.8 m/s^2. The vertical displacement is -150 m (since it is below the cliff).
Using these values, we get:-150 = 0 x t + 0.5 x 9.8 x t^2
Solving for t, we get:t = 5.01 seconds
The horizontal displacement is therefore:
horizontal displacement = 800 x 5.01
horizontal displacement = 4008 meters
3. To find the launch angle, we can use the formula:
Δy = (v^2 x sin^2 θ)/2g Where Δy is the vertical displacement (26 ft), v is the initial velocity (30 ft/s), g is the acceleration due to gravity (32 ft/s^2), and θ is the launch angle.
Using these values, we get:26 = (30^2 x sin^2 θ)/2 x 32
Solving for sin^2 θ:sin^2 θ = (2 x 26 x 32)/(30^2)sin^2 θ = 0.12
Taking the square root:sin θ = 0.35θ = sin^-1 (0.35)θ = 20.5°
Therefore, the launch angle should be approximately 20.5°.
Note: The given measurements are in feet, but the calculations are done in fps (feet per second).
Learn more about horizontal displacement here https://brainly.com/question/6107697
#SPJ11
An LED lamp has a 700 lx intensity at a distance of 1.0 m.
What is the intensity of the
lamp at 6.5 m away?
The intensity of the LED lamp at a distance of 6.5 m away is approximately 16.59 lx.
To calculate the intensity of the LED lamp at a distance of 6.5 m away, we can use the inverse square law, which states that the intensity of light decreases inversely proportional to the square of the distance.
Given:
Initial intensity (I1) = 700 lx
Initial distance (d1) = 1.0 m
Target distance (d2) = 6.5 m
The formula to calculate the intensity at the target distance is:
I2 = I1 * (d1 / d2)^2
Substituting the given values:
I2 = 700 lx * (1.0 m / 6.5 m)^2
Calculating the value:
I2 = 700 lx * (0.1538)^2
I2 ≈ 700 lx * 0.0237
I2 ≈ 16.59 lx
Therefore, the intensity of the LED lamp at a distance of 6.5 m away is approximately 16.59 lx.
To know more about distance, click here:
brainly.com/question/15172156
#SPJ11
Q/C S A glider of mass m is free to slide along a horizontal air track. It is pushed against a launcher at one end of the track. Model the launcher as a light spring of force constant k compressed by a distance x. The glider is released from rest. (c) Is more work done on a cart with a large or a small mass?
More work is done on a cart with a small mass. This relationship arises from the work-energy principle, which states that the work done on an object is equal to the change in its kinetic energy.
To understand why more work is done on a cart with a small mass, let's consider the work-energy principle. According to this principle, the work done on an object is equal to the change in its kinetic energy.
In this scenario, when the glider is released from rest, the compressed spring exerts a force on the glider, accelerating it along the air track. The work done by the spring force is given by the formula:
Work = (1/2) kx²
where k is the force constant of the spring and x is the distance the spring is compressed.
Now, the change in kinetic energy of the glider can be calculated using the formula:
ΔKE = (1/2) mv²
where m is the mass of the glider and v is its final velocity.
From the work-energy principle, we can equate the work done by the spring force to the change in kinetic energy:
(1/2) kx² = (1/2) mv²
Since the initial velocity of the glider is zero, the final velocity v is equal to the square root of (2kx²/m).
Now, let's consider the situation where we have two gliders with different masses, m₁ and m₂, and the same spring constant k and compression x. Using the above equation, we can see that the final velocity of the glider is inversely proportional to the square root of its mass:
v ∝ 1/√m
As a result, a glider with a smaller mass will have a larger final velocity compared to a glider with a larger mass. This indicates that more work is done on the cart with a smaller mass since it achieves a greater change in kinetic energy.
More work is done on a cart with a small mass compared to a cart with a large mass. This is because, in the given scenario, the final velocity of the glider is inversely proportional to the square root of its mass. Therefore, a glider with a smaller mass will experience a larger change in kinetic energy and, consequently, more work will be done on it.
This relationship arises from the work-energy principle, which states that the work done on an object is equal to the change in its kinetic energy. Understanding this concept helps in analyzing the energy transfer and mechanical behavior of objects in systems involving springs and masses.
To know more about kinetic energy ,visit:
https://brainly.com/question/8101588
#SPJ11
In conservation of energy experiment, the relation between the hanging mass (m) and the increase in the length (x) is given by: mg =kx Where (k) is the spring constant and (g) is the acceleration due to gravity (g = 9.81 m/s2). The graph below shows (m vs. x) for three different springs. Which spring has the lowest spring constant (ks)? Spring 2 Spring 3 Spring 1 All the springs have the same Tidliging mass (m) and the increase in the length (x) is given mg =kx Spring (slope - 2km) Spring 2 (slope 1.7km) Spring 3 slope 2.5km) g) is the acceleration due to gravity (g = 9.81 m/s2). The graph below shows (m vs.
Spring 2 has the lowest spring constant among the three springs in the experiment.
In the given conservation of energy experiment, the relation between the hanging mass (m) and the increase in length (x) is given by mg = kx, where k is the spring constant and g is the acceleration due to gravity (9.81 m/s²).
The graph provided shows the relationship between m and x for three different springs. To determine which spring has the lowest spring constant, we need to compare the slopes of the graph lines. The spring with the lowest slope, which represents the smallest value of k, has the lowest spring constant.
The slope of the graph represents the spring constant (k) in the relation mg = kx. A steeper slope indicates a higher spring constant, while a flatter slope indicates a lower spring constant. Looking at the graph lines for the three springs, we can compare their slopes to determine which one has the lowest spring constant.
If the slope of Spring 1 is 2k, the slope of Spring 2 is 1.7k, and the slope of Spring 3 is 2.5k, we can conclude that Spring 2 has the lowest spring constant (ks). This is because its slope is the smallest among the three, indicating a smaller value for k.
Therefore, Spring 2 has the lowest spring constant among the three springs in the experiment.
Learn more about spring here: brainly.com/question/14670501
#SPJ11
A particle starts from the origin at t=0.0 s with a velocity of 5.2 i m/s and moves in the xy plane with a constant acceleration of (-5.4 i + 1.6 j)m/s?. When the particle achieves
the maximum positive -coordinate, how far is it from the origin?
When the particle achieves the maximum positive y-coordinate, it is at a distance of 0 meters from the origin. This means it is still at the origin in the xy plane, as its x-coordinate remains zero throughout its motion.
The distance of the particle from the origin when it achieves the maximum positive y-coordinate, we need to analyze its motion in the xy plane.
Initial velocity, u = 5.2 i m/s
Acceleration, a = (-5.4 i + 1.6 j) m/s²
We can integrate the acceleration to find the velocity components as a function of time:
v_x = ∫(-5.4) dt = -5.4t + c₁
v_y = ∫1.6 dt = 1.6t + c₂
Applying the initial condition at t = 0, we have:
v_x(0) = 5.2 i m/s = c₁
v_y(0) = 0 j m/s = c₂
Therefore, the velocity components become:
v_x = -5.4t + 5.2 i m/s
v_y = 1.6t j m/s
Next, we integrate the velocity components to find the position as a function of time:
x = ∫(-5.4t + 5.2) dt = (-2.7t² + 5.2t + c₃) i
y = ∫1.6t dt = (0.8t² + c₄) j
Applying the initial condition at t = 0, we have:
x(0) = 0 i m = c₃
y(0) = 0 j m = c₄
Therefore, the position components become:
x = (-2.7t² + 5.2t) i m
y = (0.8t²) j m
To find the maximum positive y-coordinate, we set y = 0.8t² = 0. The time when y = 0 is t = 0.
Plugging this value of t into the x-component equation, we have:
x = (-2.7(0)² + 5.2(0)) i = 0 i m
Therefore, at the time when the particle achieves the maximum positive y-coordinate, it is at a distance of 0 meters from the origin.
Learn more about ” velocity ” here:
brainly.com/question/30559316
#SPJ11
A raindrop of mass 3.35× 10⁻⁵ kg falls vertically at constant speed under the influence of gravity and air resis-tance. Model the drop as a particle. As it falls 100m, what is the work done on the raindrop(b) by air resistance?
The work done by gravity is equal to the work done by air resistance, the work done on the raindrop by air resistance is also 3.27×10⁻² J.
This means that the work done by gravity is equal to the work done by air resistance.
The work done by gravity can be calculated using the formula: Work = force x distance. The force of gravity acting on the raindrop is given by the equation: F = mg, where m is the mass of the raindrop and g is the acceleration due to gravity (9.8 m/s²).
First, we need to calculate the force of gravity acting on the raindrop. The mass of the raindrop is given as 3.35×10⁻⁵ kg. Therefore, the force of gravity can be calculated as:
F = mg
F = (3.35×10⁻⁵ kg) x (9.8 m/s²)
F = 3.27×10⁻⁴ N
Next, we calculate the work done by gravity over a distance of 100 m:
Work = force x distance
Work = (3.27×10⁻⁴ N) x (100 m)
Work = 3.27×10⁻² J
Since the work done by gravity is equal to the work done by air resistance, the work done on the raindrop by air resistance is also 3.27×10⁻² J.
To know more about resistance visit:
https://brainly.com/question/33728800
#SPJ11
Susan's 10.0 kg baby brother Paul sits on a mat. Susan pulls the mat across the floor using a rope that is angled 30∘ above the floor. The tension is a constant 31.0 N and the coefficient of friction is 0.210.
Use work and energy to find Paul's speed after being pulled 2.90 m .
Paul's speed after being pulled at distance of 2.90 m is approximately 2.11 m/s
Mass of Paul (m) = 10.0 kg
Angle of the rope (θ) = 30°
Tension force (T) = 31.0 N
Coefficient of friction (μ) = 0.210
Distance pulled (d) = 2.90 m
First, let's calculate the work done by the tension force:
Work done by tension force (Wt) = T * d * cos(θ)
Wt = 31.0 N * 2.90 m * cos(30°)
Wt = 79.741 J
Next, let's calculate the work done by friction:
Work done by friction (Wf) = μ * m * g * d
where g is the acceleration due to gravity (approximately 9.8 m/s²)
Wf = 0.210 * 10.0 kg * 9.8 m/s² * 2.90 m
Wf = 57.471 J
The net work done on Paul is the difference between the work done by the tension force and the work done by friction:
Net work done (Wnet) = Wt - Wf
Wnet = 79.741 J - 57.471 J
Wnet = 22.270 J
According to the work-energy principle, the change in kinetic energy (ΔKE) is equal to the net work done:
ΔKE = Wnet
ΔKE = 22.270 J
Since Paul starts from rest, his initial kinetic energy is zero (KE_initial = 0). Therefore, the final kinetic energy (KE_final) is equal to the change in kinetic energy:
KE_final = ΔKE = 22.270 J
We can use the kinetic energy formula to find Paul's final speed (v):
KE_final = 0.5 * m * v²
22.270 J = 0.5 * 10.0 kg * v²
22.270 J = 5.0 kg * v²
Dividing both sides by 5.0 kg:
v² = 4.454
Taking the square root of both sides:
v ≈ 2.11 m/s
Therefore, Paul's speed after being pulled at a distance of 2.90 m is approximately 2.11 m/s.
Learn more about tension force:
https://brainly.com/question/30343908
#SPJ11
A700-tum solenoid, 24 cm long has a diameter of 2.7 cm A11-turn coil is wound tightly around the center of the solenoid . If the current in the solenoid increases uniformily from 0 to 42 A in 0 60 s, what will be the induced emf in the short coll during this time? Express your answer to two significant figures and include the appropriate units.
The induced emf in the short coil during this time is -1.12 × 10⁻⁸ V. The formula to calculate the induced emf in the short coil during this time is given by the following formula:ε=−N(ΔΦ/Δt)
The formula to calculate the induced emf in the short coil during this time is given by the following formula:ε=−N(ΔΦ/Δt)where N is the number of turns in the short coil and ΔΦ/Δt is the change in the magnetic flux over time. The change in magnetic flux over time is given by the following formula:
ΔΦ/Δt=μ_0NA(ΔI/Δt)where μ0 is the permeability of free space, A is the cross-sectional area of the solenoid, and ΔI/Δt is the rate of change of current in the solenoid.
Substituting the values given in the question: μ0 = 4π × 10⁻⁷ T·m/A,
N = 11, A = (π/4) × (2.7 × 10⁻² m)²
= 5.73 × 10⁻⁴ m²,
ΔI/Δt = 42 A/60 s
= 0.7 A/s,
we have: ΔΦ/Δt =4π × 10⁻⁷ T·m/A × 11 × 5.73 × 10⁻⁴ m² × 0.7 A/s
= 1.02 × 10⁻⁹ Wb/s (2 SF)
Therefore, the induced emf in the short coil during this time is:
ε=−N(ΔΦ/Δt)
=−11 × 1.02 × 10⁻⁹ V/s
= -1.12 × 10⁻⁸ V (2 SF)
Answer: The induced emf in the short coil during this time is -1.12 × 10⁻⁸ V.
To know more about induced emf, refer
https://brainly.com/question/17329842
#SPJ11
5cm, qA = 2μC at the origin x = 0, qß = 1µC at x = : 4 cm, 2 1 cm - = X1 What is the potential difference Vx1 Vx2? Again, note the sign change on the charge. (2 points per case) Also in each case please provide the integral you are doing and then also provide your answer with units.
The potential difference between Vx1 Vx2 when x1 = 4cm, and x2 = 2 cm . The formula for potential difference is given by V = VB - VA Where VB is the potential at point B, and VA is the potential at point A.
Integral formula: Potential difference is defined as the work done per unit charge to move a charge from one point to another, and is represented mathematically as the line integral of the electric field between the two points in question, as shown below:
V = - ∫E.ds
Where, E is the electric field, ds is an infinitesimal element of the path taken by the charge, and the integral is taken along the path between the two points in question. Here, E can be determined using Coulomb's law, given as:
F = k.q1.q2/r^2
Here, r is the distance between the two charges and k is the Coulomb's constant which is equal to 1/4πε_0. Where ε_0 is the permittivity of free space, which is equal to 8.85 x 10^-12 C^2/(N.m^2).
When x1 = 4 cm, q1 = 1 µC, q2 = - 2 µC, and x2 = 2 cm, The distance between the two charges, r = (4 - 2) cm = 2 cm = 0.02 m.
Therefore,
F = k.q1.q2/r^2 = (1/4πε_0).(1 x 10^-6) x (-2 x 10^-6)/(0.02)^2 = - 0.225 N
Using the formula for electric potential,
Vx1 - Vx2 = ∫E.dx = (- 0.225) x 10^3 x ∫(2 - 4)/100 dx = (0.225) x 10^3 x ∫2/100 - 4/100 dx= (0.225) x 10^3 x (- 2/100) = -4.5V
Therefore, the potential difference Vx1 Vx2 is equal to - 4.5 V.
learn more about potential difference
https://brainly.com/question/23716417
#SPJ11
:
A child bounces a super ball on the sidewalk, the linear impulse delivered by the sidewalk is 2N.s during the 1/800 s of contact, what is the magnitude of the average force exerted on the ball by the sidewalk.
The magnitude of the average force exerted on the ball by the sidewalk is 1600 N.
The impulse momentum theorem states that the change in momentum of an object is equal to the impulse acting on it. When a child bounces a super ball on the sidewalk, the linear impulse delivered by the sidewalk is 2N.s during the 1/800 s of contact.
This means that the impulse acting on the ball is 2 N.s, and it occurs over a time of 1/800 s. We can use this information to determine the magnitude of the average force exerted on the ball by the sidewalk. The impulse momentum theorem is expressed as:
I = Δp where I is the impulse and Δp is the change in momentum. We can rearrange this equation to solve for the change in momentum: Δp = I
momentum is expressed as: p = mv where p is momentum, m is mass, and v is velocity. Since the mass of the ball remains constant, we can simplify this equation to: p = mv = mΔv where Δv is the change in velocity. We can now substitute this expression for momentum into the impulse momentum theorem equation: Δp = I = mΔv
Solving for Δv, we get: Δv = I/m
We know that the impulse acting on the ball is 2 N.s and that it occurs over a time of 1/800 s. To determine the average force exerted on the ball by the sidewalk, we need to calculate the change in velocity. However, we do not know the mass of the ball. Therefore, we will assume a mass of 1 kg, which is reasonable for a super ball. Using this assumption, we can calculate the change in velocity:
Δv = I/m
= 2 N.s / 1 kg
= 2 m/s
The average force exerted on the ball by the sidewalk is equal to the rate of change of momentum, which is given by:F = Δp / t where t is the time over which the force is applied. Since the force is applied over a time of 1/800 s, we can substitute this value into the equation:
F = Δp / t = mΔv / t
= (1 kg)(2 m/s) / (1/800 s)
= 1600 N
The magnitude of the average force exerted on the ball by the sidewalk is 1600 N. This means that the sidewalk exerts a strong force on the ball to change its direction. It also means that the ball exerts an equal and opposite force on the sidewalk, as required by Newton's third law of motion.
Answer: The magnitude of the average force exerted on the ball by the sidewalk is 1600 N.
To know more about Newton's third law of motion, visit:
https://brainly.com/question/974124
#SPJ11
The magnitude of the average force exerted on the ball by the sidewalk is 1600 N.
We have been given the following:Linear impulse delivered by the sidewalk = 2 N
The impulse delivered by the sidewalk can be calculated using the formula:
Impulse = Force * Time
Given that the impulse delivered is 2 N·s and the contact time is 1/800 s, we can rearrange the equation to solve for the average force:
Force = Impulse / Time
Substituting the values:
Force = 2 N·s / (1/800 s)
Force = 2 N·s * (800 s)
Force = 1600 N
Therefore, the magnitude of the average force exerted on the ball by the sidewalk is 1600 N.
To know more about magnitude, visit:
https://brainly.com/question/31022175
#SPJ11
maximum. The slit-screen distance is L=91.2 cm, and a=0.600 mm. What is the wavelength (in nm ) of the incident light? nm
The wavelength of the incident light is 152 nm.
When the intensity pattern is measured by a diffraction pattern created by a double-slit, the maximum intensity is obtained by the center of the pattern. The slit-screen distance L=91.2 cm and a=0.600 mm.
What is the wavelength (in nm ) of the incident light?
The formula to calculate wavelength λ of the incident light is given as
:λ = xL/a
Where, x = 1,
for the maximum So, putting the values in the above formula,
we get: λ = xL/aλ
= (1 × 91.2)/0.600
=152
The wavelength of the incident light is 152 nm.
To calculate the wavelength of incident light, λ using double slit experiment. It is given that the maximum intensity is obtained by the center of the pattern, thus according to the formula derived by Young for the maxima and minima is:
dsinθ = mλ
where, d is the distance between the slits, θ is the angle of diffraction, m is the order of diffraction.
By putting the values in the above formula, we get:
mλ = d sin θ
Where, m = 1λ
= d sin θ
The distance between the slits is not given in the question. Hence, we will use another formula,λ = xL/a
Where, x = 1, for the maximum
λ = xL/aλ
= (1 × 91.2)/0.600
=152
To know more about wavelength visit:
https://brainly.com/question/31143857
#SPJ11
A stiff wire 41.0 cm long is bent at a right angle in the middle. One section lies along the z axis and the other is along the line y = 2x in the xy plane. A current of 23.5 A flows in the wire-down the z axis and out the line in the xy plane. The wire passes through a uniform magnetic field given by B = (0.318i) T. Determine the magnitude and direction of the total force on the wire.
The magnitude of the total force on the wire is 0.968 N and it is directed along the negative y axis.
What is force?A force is a pull or push upon an object resulting from the object's interaction with another object. Forces can cause an object to change its motion or velocity.
In this case, the wire is experiencing a magnetic force due to the current in the wire and a magnetic field acting on it. To calculate the magnitude and direction of the total force on the wire, we can use the right-hand rule for magnetic forces. According to this rule, if the thumb of the right hand points in the direction of the current, and the fingers point in the direction of the magnetic field, then the palm will point in the direction of the force.
Let's begin by determining the magnitude of the magnetic force on each section of the wire.
Magnetic force on the section of the wire that lies along the z-axis:
Magnetic force on the section of the wire that lies along the line y = 2x in the xy plane:
Now, we need to calculate the total force on the wire by adding up the forces on each section of the wire. Since the forces are at right angles to each other, we can use the Pythagorean theorem to find the magnitude of the total force.
Ftotal² = Fz² + Fy²Ftotal² = (0.288 N)² + (0.792 N)²F
total = 0.849 N
Now, we need to find the direction of the total force. According to the right-hand rule for magnetic forces, the force on the section of the wire that lies along the line y = 2x in the xy plane is directed along the negative y-axis. Therefore, the total force on the wire is also directed along the negative y-axis.
Thus, the magnitude of the total force on the wire is 0.849 N, and it is directed along the negative y-axis.
learn more about force here
https://brainly.com/question/12785175
#SPJ11
Suppose you move 10 Coulombs of charge from point 1 to point 2.
Doing so costs you 50 Joules. What is the magnitude of the voltage
difference between points 1 and 2?
0.2 V
50 V
5.0 V
500 V
0.50 V
The magnitude of the voltage difference between points 1 and 2 is 5.0 V. Voltage is defined as the electric potential difference between two points in an electric field.
It represents the amount of energy required to move a unit charge from one point to another. In this scenario, you moved 10 Coulombs of charge from point 1 to point 2, and it cost you 50 Joules of energy. The voltage difference is calculated by dividing the energy (in Joules) by the charge (in Coulombs). Therefore, the voltage difference between the two points is 50 J / 10 C = 5.0 V.
When moving 10 Coulombs of charge between point 1 and point 2 costs 50 Joules of energy, the magnitude of the voltage difference between the two points is 5.0 Volts.
Learn more about voltage difference click here: brainly.com/question/118936
#SPJ11
Spinning Ice Skater (a) Calculate the angular momentum of an ice skater spinning at 6.00 rev/s ( 37.7 rad/s) given his moment of inertia is 0.4100 kg-m? (Moment of inertia is the same quantity as rotational inertia.) L = 15.457 kg m^2 (b) He reduces his rate of spin (his angular velocity) by extending his arms and increasing his moment of inertia. Find the value of his new moment of inertia if his angular velocity drops to 2.40 rev/s. I = 2.46 kg m 2 x Your response differs from the correct answer by more than 100%. לס (c) Suppose instead he keeps his arms in and allows friction with the ice to slow him to 3.00 rev/s (18.85 rad/s). What average torque was exerted if this takes 12.0 seconds? (Hint: consider the torque (and angular acceleration) to be constant so this is an analog to the constant acceleration problems. The torque is negative as it slows a positive rotation speed.) cal
a) The formula for angular momentum is given by the product of moment of inertia and angular velocity. That is,L = Iω, where[tex]L = 15.457 kg m^2[/tex] is angular momentumI = 0.4100 kg-m is moment of inertiaω = 37.7 rad/s is angular velocity.
Thus,[tex]L = Iω = 0.4100 × 37.7 = 15.457 kg m^2[/tex]. Hence, the angular momentum of the ice skater is [tex]15.457 kg m^2.b[/tex]) The ice skater reduces his rate of spin by extending his arms and increasing his moment of inertia. We need to find the new moment of inertia if his angular velocity drops to 2.40 rev/s.
We have the formula L = Iω. Rearranging the formula gives I = L/ω.Let I1 be the initial moment of inertia of the ice skater, I2 be the final moment of inertia of the ice skater, ω1 be the initial angular velocity, and ω2 be the final angular velocity. The angular momentum of the ice skater remains constant. Therefore[tex],L = I1ω1 = I2ω2Thus, I2 = (I1ω1)/ω2 = (0.4100 × 37.7)/2.40 = 6.43 kg m^2.\\[/tex]
The new moment of inertia of the ice skater is [tex]6.43 kg m^2.[/tex]c) The average torque exerted on the ice skater can be calculated using the formula τ = (ΔL)/Δt, where ΔL is the change in angular momentum, and Δt is the change in time.We have the initial angular velocity, ω1 = 6.00 rev/s, and the final angular velocity, ω2 = 3.00 rev/s.
The change in angular velocity is given by[tex]Δω = ω2 - ω1 = 3.00 - 6.00 = -3.00 rev/s[/tex].The change in time is given by Δt = 12.0 s. The change in angular momentum is given by,ΔL = L2 - L1, where L1 is the initial angular momentum and L2 is the final angular momentum. Since the ice skater is slowing down, ΔL is negative
[tex].L1 = I1ω1 = 0.4100 × 37.7 = 15.457 kg m^2L2 = I2ω2, \\\\[/tex]
where I2 is the moment of inertia when his arms are in. We have already calculated I2 to be 6.43 kg m^2. Thus,L2 = 6.43 × 18.85 = 121.25 kg m^2Therefore,ΔL = L2 - L1 = 121.25 - 15.457 = 105.79 kg m[tex]ΔL = L2 - L1 = 121.25 - 15.457 = 105.79 kg m^2[/tex]2Putting the values in the formula, we get,[tex]τ = (ΔL)/Δt= (-105.79)/12.0=-8.81 N m\\[/tex].Hence, the average torque exerted on the ice skater if it takes 12.0 s for him to slow to 3.00 rev/s is -8.81 N m.
To know about inertia visit:
https://brainly.com/question/3268780
#SPJ11
Pressure drop between two sections of a unifrom pipe carrying water is 9.81 kPa. Then the head loss due to friction is 1.981 m 2.0.1 m 3.10 m 4.1m
For oil flow through a pipe, velocity increases 1. with increase in pressure at a cross section 2, with decrease in area of cross section 3. with increase in area of cross section 4. Does not depend on the area of cross section
For oil flow through a pipe, velocity increases with increase in area of cross section. Option 3 is correct.
To determine the head loss due to friction in a pipe, we can use the Darcy-Weisbach equation:
ΔP = λ * (L/D) * (ρ * V² / 2)
Where:
ΔP is the pressure drop (given as 9.81 kPa)
λ is the friction factor
L is the length of the pipe
D is the diameter of the pipe
ρ is the density of the fluid (water in this case)
V is the velocity of the fluid
We can rearrange the equation to solve for the head loss (H):
H = (ΔP * 2) / (ρ * g)
Where g is the acceleration due to gravity (9.81 m/s²).
Given the pressure drop (ΔP) of 9.81 kPa, we can calculate the head loss due to friction.
H = (9.81 kPa * 2) / (ρ * g)
Now, let's address the second part of your question regarding oil flow through a pipe and how velocity changes with respect to pressure and cross-sectional area.
With an increase in pressure at a cross section: When the pressure at a cross section increases, it typically results in a decrease in velocity due to the increased resistance against flow.
With a decrease in area of the cross section: According to the principle of continuity, when the cross-sectional area decreases, the velocity of the fluid increases to maintain the same flow rate.
With an increase in area of the cross section: When the cross-sectional area increases, the velocity of the fluid decreases to maintain the same flow rate.
The velocity does not depend solely on the area of the cross section. It is influenced by various factors such as pressure, flow rate, and pipe properties.
Therefore, the correct answer to the question is option 4: The velocity does not depend on the area of the cross section alone.
To know more about the Cross section, here
https://brainly.com/question/19365250
#SPJ4
You go for a walk and travel 27.0 m at an angle 24 East of North. You then walk 35.4 m and an angle 32 South of East. What is the magnitude of your displacement vector in metres?
The magnitude of your displacement vector is approximately 55.10 meters. To find the magnitude of the displacement vector, we need to calculate the resultant vector by adding the two vectors together.
For the first vector (27.0 m at an angle 24° east of north):
27.0 m * sin(24°) = 11.07 m (northward)
27.0 m * cos(24°) = 24.71 m (eastward)
For the second vector (35.4 m at an angle 32° south of east):
The east component is given by:
35.4 m * cos(32°) = 29.83 m (eastward)
The south component is given by:
35.4 m * sin(32°) = 18.60 m (southward)
11.07 m (northward) - 18.60 m (southward) = -7.53 m (southward)
And let's add the east components together:
24.71 m (eastward) + 29.83 m (eastward) = 54.54 m (eastward)
So, the resultant vector is 54.54 m eastward and -7.53 m southward.
To find the magnitude of the displacement vector, we can use the Pythagorean theorem:
magnitude = sqrt((eastward)^2 + (southward)^2)
magnitude = sqrt((54.54 m)^2 + (-7.53 m)^2)
magnitude ≈ 55.10 m
Therefore, the magnitude of your displacement vector is approximately 55.10 meters.
Learn more about magnitude here : brainly.com/question/31022175
#SPJ11
The x vector component of a displacement vector ; has a magnitude of 132 m and points along the negative x axis. The y vector component has a magnitude of 171 m and points along the negative y axis. Find (a) the magnitude and (b) direction of *. Specify the direction as a positive
angle with respect to the negative x axis.
(a) The magnitude of the displacement vector is approximately 215.91 m.
(b) The direction of the displacement vector, measured as a positive angle with respect to the negative x-axis, is approximately 52.12 degrees.
To find the magnitude and direction of the displacement vector, we can use the Pythagorean theorem and trigonometry.
x-component magnitude = 132 m (along the negative x-axis)
y-component magnitude = 171 m (along the negative y-axis)
(a) Magnitude of the displacement vector:
The magnitude (|D|) of the displacement vector can be calculated using the Pythagorean theorem:
|D| = sqrt((x-component)^2 + (y-component)^2)
|D| = sqrt((132 m)^2 + (171 m)^2)
|D| ≈ sqrt(17424 m^2 + 29241 m^2)
|D| ≈ sqrt(46665 m^2)
|D| ≈ 215.91 m
Therefore, the magnitude of the displacement vector is approximately 215.91 m.
(b) Direction of the displacement vector:
To determine the direction of the displacement vector, we can use trigonometry. The direction can be expressed as a positive angle with respect to the negative x-axis.
tan(θ) = (y-component) / (x-component)
tan(θ) = (-171 m) / (-132 m) [Note: negative signs cancel out]
tan(θ) ≈ 1.2955
θ ≈ tan^(-1)(1.2955)
θ ≈ 52.12 degrees
Therefore, the direction of the displacement vector, measured as a positive angle with respect to the negative x-axis, is approximately 52.12 degrees.
Learn more about displacement vectors at https://brainly.com/question/12006588
#SPJ11
What is the minimum stopping distance for the same car traveling at a speed of 36 m/s ?
The minimum stopping distance for the car traveling at a speed of 36 m/s is 117 meters.
The minimum stopping distance for a car can be calculated using the formula:
Stopping Distance = Thinking Distance + Braking Distance
The thinking distance is the distance the car travels while the driver reacts to a situation and applies the brakes. The braking distance is the distance the car travels while braking to a stop.
To calculate the thinking distance, we can use the formula: Thinking Distance = Speed x Reaction Time.
Given that the car is traveling at a speed of 36 m/s, we need to know the reaction time of the driver to calculate the thinking distance. Let's assume a typical reaction time of 1 second for this example.
Thinking Distance = 36 m/s x 1 s = 36 m
To calculate the braking distance, we need to use the formula: Braking Distance = (Speed 2) / (2 x Deceleration)
Deceleration is the rate at which the car slows down. Let's assume a deceleration of 8 m/s^2 for this example.
Braking Distance = (36 m/s) 2 / (2 x 8 m/s 2) = 81 m
Therefore, the minimum stopping distance for the same car traveling at a speed of 36 m/s is the sum of the thinking distance and the braking distance:
Stopping Distance = 36 m + 81 m = 117 m
The minimum stopping distance for the car traveling at a speed of 36 m/s is 117 meters.
To know more distance visit:
brainly.com/question/15172156
#SPJ11
Determine the entropy of 1500 g of water vapor at 125°C (Specific heat capacity of ice =2090 JkgK-4, water 4200 Jkg +K-1, water vapor steam = 1996 Jkg-4K-1, latent heat of fusion of water = 3.33x105 Jkg - and vaporization is 2260 Jkg:-). (7)
The entropy of 1500 g of water vapor at 125°CThe entropy of 1500 g of water vapor at 125°C can be calculated by using the formula mentioned below:S = mcΔT+ml
Where,S = entropy, m = mass,c = specific heat capacity, ΔT = change in temperature,
l = latent heat of fusion/melting
First, the latent heat of the vaporization of water needs to be calculated:
Q = ml = 2260 Jkg-1.
Therefore, for 1500 g of water vapor, the latent heat of vaporization can be calculated as:
L = Q × m = 2260 Jkg-1 × 1.5 kg= 3.39 × 103 J.
Now, the specific heat capacity of water vapor needs to be calculated using the formula mentioned below:
c = Q/mΔT
Here, the mass of water vapor = 1500 g = 1.5 kg
ΔT = 125°C - 100°C = 25°C = 298 K
So, the specific heat capacity of water vapor = 1996 Jkg-4K-1.
So, the entropy of 1500 g of water vapor at 125°C can be calculated using the formula mentioned above as
S = mcΔT+ml
= (1.5 kg × 1996 Jkg-4K-1 × 298 K) + 3.39 × 103 J
= 8.92 × 105 J/K.
=13.38J/K.
The entropy of 1500 g of water vapor at 125°C is13.38J/K.
Learn more about entropy and the latent heat of vaporization https://brainly.com/question/14514465
#SPJ11
Problem 3. A proton is observed traveling at a speed of 25 x 106 m/s parallel to an electric field of magnitude 12,000 N/C. How long will it take for this proton t negative plate and comes to a stop?
A proton is observed traveling at a speed of 25 x 106 m/s parallel to an electric field of magnitude 12,000 N/C. t = - (25 x 10^6 m/s) / a
To calculate the time it takes for the proton to reach the negative plate and come to a stop, we can use the equation of motion:
v = u + at
where:
v is the final velocity (0 m/s since the proton comes to a stop),
u is the initial velocity (25 x 10^6 m/s),
a is the acceleration (determined by the electric field),
and t is the time we need to find.
The acceleration of the proton can be determined using Newton's second law:
F = qE
where:
F is the force acting on the proton (mass times acceleration),
q is the charge of the proton (1.6 x 10^-19 C),
and E is the magnitude of the electric field (12,000 N/C).
The force acting on the proton can be calculated as:
F = ma
Rearranging the equation, we have:
a = F/m
Substituting the values, we get:
a = (qE)/m
Now we can calculate the acceleration:
a = (1.6 x 10^-19 C * 12,000 N/C) / mass_of_proton
The mass of a proton is approximately 1.67 x 10^-27 kg.
Substituting the values, we can solve for acceleration:
a = (1.6 x 10^-19 C * 12,000 N/C) / (1.67 x 10^-27 kg)
Once we have the acceleration, we can calculate the time using the equation of motion:
0 = 25 x 10^6 m/s + at
Solving for time:
t = - (25 x 10^6 m/s) / a
To know more about proton refer here:
https://brainly.com/question/12535409#
#SPJ11
The magnetic field in a traveling EM wave has an rms strength of 20.5 nt. v Part A How long does it take to deliver 345 J of energy to 1.05 cm? of a wall that it hits perpendicularly? Express your answer with the appropriate units. Δt = Value Units Submit
It takes approximately 81.02 seconds for the EM wave to deliver 345 J of energy to the 1.05 cm² wall that it hits perpendicularly.
Given:
B = 20.5 × 10^(-9) T
A = 1.1025 × 10^(-8) m²
E = 345 J
c = 2.998 × 10^8 m/s
ε₀ = 8.854 × 10^(-12) F/m
First, let's calculate the power:
P = (1/2) * ε₀ * E² * A * c
P = (1/2) * (8.854 × 10^(-12) F/m) * (345 J)² * (1.1025 × 10^(-8) m²) * (2.998 × 10^8 m/s)
Using the given values, the power P is approximately 4.254 W.
Now, we can calculate the time:
Δt = E / P
Δt = 345 J / 4.254 W
Calculating the division, we find that Δt is approximately 81.02 seconds.
Therefore, it takes approximately 81.02 seconds for the EM wave to deliver 345 J of energy to the 1.05 cm² wall that it hits perpendicularly.
Learn more about EM wave:
https://brainly.com/question/13803241
#SPJ11
A conducting sphere of radius a, having a total charge Q, is
situated in an electric field initially
uniform, E0. Determine the potential at all points outside the
sphere.
The potential at all points outside a conducting sphere of radius a, with a total charge Q, situated in an initially uniform electric field E0, is the same as the potential due to a point charge Q located at the center of the sphere.
The potential is given by the equation V = kQ/r, where V is the potential, k is the electrostatic constant, Q is the charge, and r is the distance from the center of the sphere to the point.
When a conducting sphere is placed in an electric field, the charges on the surface of the sphere redistribute themselves in such a way that the electric field inside the sphere becomes zero.
Therefore, the electric field outside the sphere is the same as the initial uniform electric field E0.
Since the electric field outside the sphere is uniform, the potential at any point outside the sphere can be determined using the formula for the potential due to a point charge.
The conducting sphere can be considered as a point charge located at its center, with charge Q.
The potential V at a point outside the sphere is given by the equation V = kQ/r, where k is the electrostatic constant ([tex]k = 1/4πε0[/tex]), Q is the total charge on the sphere, and r is the distance from the center of the sphere to the point.
Therefore, the potential at all points outside the conducting sphere is the same as the potential due to a point charge Q located at the center of the sphere, and it can be calculated using the equation V = kQ/r.
To learn more about, sphere of radius:-
brainly.com/question/33261344
#SPJ11
A normal person has a near point at 25 cm and a far point at infinity. Suppose a nearsighted person has a far point at 157 cm. What power lenses would prescribe?
To correct the nearsightedness of a person with a far point at 157 cm, lenses with a power of approximately -0.636 diopters (concave) should be prescribed. Consultation with an eye care professional is important for an accurate prescription and fitting.
To determine the power of lenses required to correct the nearsightedness of a person, we can use the formula:
Lens Power (in diopters) = 1 / Far Point (in meters)
Given that the far point of the nearsighted person is 157 cm (which is 1.57 meters), we can substitute this value into the formula:
Lens Power = 1 / 1.57 = 0.636 diopters
Therefore, a nearsighted person with a far point at 157 cm would require lenses with a power of approximately -0.636 diopters. The negative sign indicates that the lenses need to be concave (diverging) in nature to help correct the person's nearsightedness.
These lenses will help diverge the incoming light rays, allowing them to focus properly on the retina, thus improving distance vision for the individual. It is important for the individual to consult an optometrist or ophthalmologist for an accurate prescription and proper fitting of the lenses based on their specific needs and visual acuity.
To learn more about lenses
https://brainly.com/question/28039799
#SPJ11
Question 4: For an electromagnetic plane wave, the electric field is given by: E=E0cos(kz+ωt)x^+0y^+0z^ a) Determine the direction of propagation of the electromagnetic wave. b) Find the magnitude and direction of the magnetic field for the given electromagnetic wave B. You may want to use some of the properties of the plane wave approximation and the Poynting vector to avoid doing vector calculus. c) Calculate the Poynting vector (magnitude and direction) associated with this electromagnetic wave. What direction does this vector point? Does this makes sense? d) If the amplitude of the magnetic field was measured to be 2.5∗10−7 T, determine numerical values for the amplitude of the electric field and the Poynting vector.
(a) The direction of propagation of the electromagnetic wave is in the positive x-axis direction.
(b) The magnitude and direction of the magnetic field can be found using the relationship between the electric field and magnetic field in an electromagnetic wave.
(c) The Poynting vector S, which represents the direction and magnitude of the electromagnetic wave's energy flow
(a)The direction of propagation is determined by the direction of the wavevector, which in this case is given by k = kz âx. Since the coefficient of âx is positive, it indicates that the wave is propagating in the positive x-axis direction.
(b)According to the wave equation, the magnetic field B is related to the electric field E by B = (1/c) E, where c is the speed of light. Therefore, the magnitude of B is |B| = |E|/c and its direction is the same as the electric field, which is in the x-axis direction.
(c) given by S = E x B. In this case, since the magnetic field B is in the x-axis direction and the electric field E is in the x-axis direction, the cross product E x B will be in the y-axis direction. Therefore, the Poynting vector points in the positive y-axis direction.
(d) Given the amplitude of the magnetic field B as 2.5 x 10⁻⁷ T, we can use the relationship |B| = |E|/c to find the amplitude of the electric field. Rearranging the equation, we have |E| = |B| x c. Plugging in the values, |E| = (2.5 x 10⁻⁷ T) x (3 x 10⁸ m/s) = 7.5 x 10¹ T. The amplitude of the Poynting vector can be calculated using |S| = |E| x |B| = (7.5 x 10¹ T) x (2.5 x 10⁻⁷ T) = 1.875 x 10⁻⁵ W/m².
In summary, for the given electromagnetic wave, the direction of propagation is in the positive x-axis direction, the magnetic field is in the positive x-axis direction, the Poynting vector points in the positive y-axis direction, and the amplitude of the electric field is 7.5 x 10¹ T and the amplitude of the Poynting vector is 1.875 x 10⁻⁵ W/m².
learn more about electromagnetic wave here:
https://brainly.com/question/3101711
#SPJ11
In a demolition derby, a car known as 'slippery Pete' has a mass of 1520 kg is moving east with a speed of 15.79 m/s. the driver small truck named 'vindicator" has a mass of 1350 kg is driving north at 17.4 m/s. when the two cars collide their bodies stick together.
what is the common speed of the cars after the collision?
a) 11.5 m/s
b) 11.7 m/s
c) 11.1 m/s
d) 11.3 m/s
Counties fairs and international events frequently feature demolition derbies.
Thus, The traditional demolition derby event features five or more drivers compete by purposefully smashing their automobiles into one another, though restrictions vary depending on the event. The winner is the last driver whose car is still in working order.
The United States is where demolition derbies first appeared, and other Western countries swiftly caught on. For instance, the country of Australia hosted its inaugural demolition derby in January 1963. Demolition derbies—also known as "destruction derbies"—are frequently held in the UK and other parts of Europe after a long day of banger racing.
Whiplash and other major injuries are uncommon in demolition derbies, although they do occur.
Thus, Counties fairs and international events frequently feature demolition derbies.
Learn more about Demolition, refer to the link:
https://brainly.com/question/15817190
#SPJ4
The correct option is (none of the above). The given masses of the cars involved in the collision are:
Mass of 'slippery Pete' = 1520 kg
Mass of 'vindicator' = 1350 kg
The given velocities of the cars involved in the collision are:
Velocity of 'slippery Pete' = 15.79 m/s
Velocity of 'vindicator' = 17.4 m/s
The initial momentum of the system is given by: P(initial) = m1v1 + m2v2
where m1 and v1 are the mass and velocity of car 1, and m2 and v2 are the mass and velocity of car 2. Substituting the given values, we get:
P(initial) = (1520 kg) (15.79 m/s) + (1350 kg) (17.4 m/s)P(initial) = 23969 + 23490P(initial) = 47459 kg m/s
Since the two cars stick together after the collision, they can be considered as a single body. The final momentum of the system is given by:P(final) = (m1 + m2) vf
where m1 and m2 are the masses of the two cars, and vf is the final velocity of the combined cars. Substituting the given values, we get:
P(final) = (1520 kg + 1350 kg) vfP(final) = 2870 kg vf
Since momentum is conserved in the system, we can equate P(initial) to P(final) and solve for vf. So:
P(initial) = P(final)47459 kg m/s = 2870 kg vf vf = 47459 kg m/s ÷ 2870 kg vf = 16.51 m/s
The common speed of the cars after the collision is 16.51 m/s, which when rounded off to one decimal place, is 16.5 m/s.Therefore, the correct option is (none of the above).
Learn more about collision from the given link
https://brainly.com/question/13138178
#SPJ11