a. The engineering value for the yield strength corresponding to U, exhibited by the steel alloy would amount to: 856.12 MPa
b. The true value for yield strength in the vicinity amounts to: 929.87 MPa
c. The 'safe stress' based on the 'factor of safety' advised would be: 232.47 MPa
In this scenario, the factor of safety is adopted to ensure the bridge can withstand loads well beyond the expected maximum. The factor of safety is typically calculated by dividing the yield strength by the applied stress.
a. The engineering value for the yield strength represents the value used in design calculations, which is lower than the true value to provide an additional safety margin. In this case, it is 856.12 MPa.
b. The true value for yield strength refers to the actual strength of the steel alloy, which is higher than the engineering value. Here, it is 929.87 MPa.
c. The 'safe stress' is calculated by dividing the yield strength by the factor of safety. It represents the maximum stress that can be applied to the structure while maintaining a sufficient safety margin. In this case, it is 232.47 MPa.
These values and calculations demonstrate the importance of considering factors of safety in engineering design to ensure the structural integrity and safety of the bridge under significant loads.
To learn more about yield strength, here
https://brainly.com/question/31664621
#SPJ4
a. The engineering value for the yield strength corresponding to U, exhibited by the steel alloy would amount to 925.73 MPa.
b. The true value for yield strength vicinity amounts to 866.12 MPa.
c. The 'safe stress' based on
the factors of safety' advised would be 232.47 MP
a. Explanation:
Given that the overall load the structure shares is 2,000,000 N, and it is distributed over two steel alloy cables with equal distribution, the load that each cable bears would be 2,000,000/2 = 1,000,000 N.
The factor of safety for the bridge, which is generally taken as 4, implies that the actual yield strength should be four times the value needed to withstand the load. Mathematically, it is expressed as;
Actual yield strength = Factor of safety * Required yield strength. The engineering value for the yield strength corresponding to U, exhibited by the steel alloy would amount to:
Let's use the formula above;
Required yield strength = Load borne by each cable/ Area of cross-section of each cable
The steel alloy of choice possesses a modulus of resilience in the vicinity of 2.07 MPa. Therefore, using the formula for modulus of resilience,
Modulus of resilience = Yield strength2 / (2 x Modulus of elasticity)Modulus of elasticity of steel is approximately 210 GPa.2.07 MPa = Yield strength2 / (2 x 210 GPa)
Yield strength = sqrt((2.07 MPa) x 2 x 210 GPa)Yield strength = 925.73 MPa
Now, the engineering value for the yield strength would amount to;
Actual yield strength = 4 x Yield strength = 4 x 925.73 MPa = 3702.92 MPa
I. 1043.65 MPa
II. 856.12 MPa
III. 621.36 MPa
IV. 925.73 MPa
Answer: IV. 925.73 MPab. The true value for yield strength vicinity amounts to:
For the true value of the yield strength, we will divide the engineering value by the factor of safety;
True yield strength = Engineering yield strength/ Factor of safety
True yield strength = 3702.92 MPa/ 4 = 925.73 MPa
I. 1053.65 MPa
II. 866.12 MPa
III. 929.87 MPa
IV. 635.23 MPa
Answer: II. 866.12 MPa
c. The 'safe stress' based on the factors of safety' advised would be:
Safe stress is a maximum allowable stress that does not cause failure in a material. For steel, the safe stress is taken as the yield strength divided by a factor of safety. Hence;
Safe stress = Yield strength/ Factor of safety
Safe stress = 925.73 MPa/ 4
I. 323.74 MPa
II. 232.47 MPa
III. 405.77 MPa
IV. 578.46 MPa
Answer: II. 232.47 MPa
Learn more about yield strength
https://brainly.com/question/30904383
#SPJ11
Prob #1 - Acetylene is hydrogenated to form ethane. The feed to the reactor contains 1.60 mol H₂/mol C₂H2. (a) Calculate the stoichiometric reactant ratio (mol H₂ react/mol C₂H₂ react) and the yield ratio (kmol C₂H6 formed/kmol H₂ react). (b) Determine the limiting reactant and calculate the percentage by which the other reactant is in excess. (c) Calculate the mass feed rate of hydrogen (kg/s) required to produce 4x106 metric tons of ethane per year, assuming that the reaction goes to completion and that the process operates for 24 hours a day, 300 days a year. (d) There is a definite drawback to running with one reactant in excess rather than feeding the reactants in stoichiometric proportion. What is it? [Hint: In the process of Part (c), what does the reactor effluent consist of and what will probably have to be done before the product ethane can be sold or used?]
(a) 1 kmol of C₂H₆ is formed per kmol of H₂ react in the reaction. (b) Percent excess of C₂H₂ is 0%. (c) Mass feed rate of H₂ is 4.33 kg/s. (d) The reactor effluent consisting of unreacted hydrogen, unreacted acetylene, ethane, methane, and other hydrocarbons will have to be separated into their respective components before the ethane product can be sold or used.
(a) Stoichiometric reactant ratio (mol H₂ react/mol C₂H₂ react)
Acetylene is hydrogenated to produce ethane according to the balanced chemical equation as follows:
C₂H₂ + 2H₂ -> C₂H₆
From the balanced chemical equation above, the stoichiometric ratio of reactants is 2 mol of hydrogen gas (H₂) to 1 mol of acetylene (C₂H₂).
This implies that 2 mol H₂ react per 1 mol C₂H₂ react. Yield Ratio (kmol C₂H₆ formed/kmol H₂ react)
According to the balanced chemical equation, 1 mol of acetylene (C₂H₂) yields 1 mol of ethane (C₂H₆) if the reaction goes to completion.
This implies that 1 kmol of C₂H₆ is formed per kmol of H₂ react in the reaction.
(b) Limiting reactant and percentage by which the other reactant is in excess
From the information given,
1.60 mol H₂/mol C₂H₂If the H₂ required for the reaction is not enough, then the reaction will be limited by H₂. The stoichiometric ratio of reactants is 2 mol of hydrogen gas (H₂) to 1 mol of acetylene (C₂H₂).
So the amount of C₂H₂ needed to react with 1.60 mol H₂ will be:1.60 mol H₂/2 mol H₂ per mol C₂H₂ = 0.80 mol C₂H₂Therefore, acetylene is the limiting reactant because there are not enough acetylene molecules to react with the available hydrogen molecules. Excess reactant = Actual amount of reactant - Limiting amount of reactantThe excess of H₂ is:
Excess H₂ = 1.60 - 0.80 = 0.80 mol H₂
Percentage by which the other reactant is in excessThe percentage by which the other reactant (acetylene) is in excess is calculated as follows:
Percent excess of C₂H₂ = (Excess C₂H₂ / Actual amount of C₂H₂) x 100%
Percent excess of C₂H₂ = (0 / 1.60) x 100% = 0%
(c) Mass feed rate of hydrogen (kg/s) required to produce 4x10^6 metric tons of ethane per year
According to the balanced chemical equation, 1 mol of acetylene (C₂H₂) yields 1 mol of ethane (C₂H₆) if the reaction goes to completion. Therefore, the molar amount of H₂ required to react with 1 mol of C₂H₂ to produce 1 mol of C₂H₆ is 2. So the mass of hydrogen required to produce 1 metric ton of ethane is:
Mass of H₂ required = 2 x (2.016 + 2.016) + 2 x 12.011 + 6 x 1.008 = 30.070 kgH₂
So the mass of H₂ required to produce 4 x 10^6 metric tons of ethane per year is:
Mass of H₂ required = 30.070 x 4 x 10^6 = 120.28 x 10^6 kg/year
The mass feed rate of hydrogen required to produce 4x10^6 metric tons of ethane per year is therefore:
Mass feed rate of H₂ = (120.28 x 10^6 kg/year)/(365 days/year x 24 hours/day x 3600 s/hour) = 4.33 kg/s
(d) The disadvantage of running with one reactant in excess is that the reactor effluent will contain unreacted excess reactant and the product ethane. Since acetylene is a gas at room temperature, it will be difficult to separate the unreacted acetylene from ethane.
In addition, any unreacted hydrogen will react with ethane in a secondary reaction, producing methane and other hydrocarbons. Therefore, the reactor effluent consisting of unreacted hydrogen, unreacted acetylene, ethane, methane, and other hydrocarbons will have to be separated into their respective components before the ethane product can be sold or used.
Learn more about hydrocarbons
https://brainly.com/question/30666184
#SPJ11
why does flash drum not need a high operating temperature as
compared to vacuum distillation?
Flash drum does not need a high operating temperature as compared to vacuum distillation because Flash drum operates at an intermediate pressure and temperature range that requires less energy to run and the feed stream vaporizes upon being released from high pressure to a lower pressure.
Flash distillation is a simple separation process that utilizes differences in the volatilities of the components in a mixture.
At a moderate pressure and temperature, the feed liquid is released into a lower pressure zone in a flash tank.
It works on the principle of flash evaporation, which occurs when a liquid is exposed to lower pressure and vaporizes instantly.
The vapor is then condensed and gathered, while the remaining liquid is collected and re-circulated via a reboiler.
The vacuum distillation process, on the other hand, is used for materials with very high boiling points that would not evaporate at temperatures below their decomposition point.
Read more about Flash Drum.
https://brainly.com/question/14925462
#SPJ11
The diagrams below are illustrations of some farm tools. Study them carefully and use
them to answer the questions that follow.
1)
iii)
M
Die
N
P
T.
Q
Identify each of the tools labelled M, N, P and Q.
Mention one use each of the tools labelled M, N, P and Q.
[4 marks]
[4 marks]
State two precautions that must be taken when using the labelled P. [2 marks].
According to the information we can infer that these tools are: P.aspersor, Q. sword, M. manual drill, N. blind. According to the above, these tools are used to build and sprinkle crops.
What tools do we see in the image?According to the image we can infer that the different tools are:
P. sprinkler.Q. sword.M. hand drill.N. blind.On the other hand, the functions of these tools are:
P. apply substances on crops.Q. Cut crops.M. Make holes.N. Make cuts.The precautions that we must take with these tools (P) are:
Good handling.Use personal protection elements.Note: This question is incomplete. Here is the complete information:
Attached image
Learn more about tools in: https://brainly.com/question/31719557
#SPJ1
For 2H₂ + O₂ → 2H₂O:
4 moles of H₂ will react with
moles of O₂ to produce
moles of H₂O
Answer:
in this reaction, 4 moles of H₂ will react with 2 moles of O₂ to produce 4 moles of H₂O.
Explanation:
The balanced equation 2H₂ + O₂ → 2H₂O tells us that 2 moles of hydrogen gas (H₂) will react with 1 mole of oxygen gas (O₂) to produce 2 moles of water (H₂O).
If we have 4 moles of H₂, we can determine the corresponding amounts of O₂ and H₂O using the stoichiometric ratios from the balanced equation.
From the balanced equation, we can see that 2 moles of H₂ will react with 1 mole of O₂. Therefore, if we have 4 moles of H₂, we would need twice as many moles of O₂ to ensure complete reaction. Thus, we would require 2 moles of O₂.
Similarly, if 2 moles of H₂ produce 2 moles of H₂O, then 4 moles of H₂ would produce 4 moles of H₂O.
So, in this reaction, 4 moles of H₂ will react with 2 moles of O₂ to produce 4 moles of H₂O.
Consider the following reaction: NO + 03 --- NO2 + O2. Which is the correct expression for the instantaneous reaction rate? Select one: 1. d102 2. 3. dt d[NO dt d[0, dt dos dt 4. V
The correct expression for the instantaneous reaction rate is given by option number 2.
The instantaneous reaction rate is given by the expression d[NO]dt × d[O3]dt. Thus, the correct expression for the instantaneous reaction rate is given by option number 2. Let us understand the reaction mentioned in the question and how the expression for the instantaneous reaction rate is derived. The given chemical equation is:
NO + O3 → NO2 + O2
The rate of the above reaction depends on the change in the concentration of any one of the reactants or products. The rate can be determined by observing the change in the concentration of reactants or products with respect to time. This change can be mathematically expressed asd[NO]dt, d[O3]dt, d[NO2]dt, d[O2]dt
Let's consider the reaction: NO + O3 → NO2 + O2The balanced chemical equation is given as:
2 NO + O3 → 2 NO2
The rate of the reaction can be determined using the rate of disappearance of O3 or NO, which is given by the following expression:d[O3]dt = -k[O3][NO]d[NO]dt = -k[O3][NO]
In order to calculate the instantaneous rate of the reaction, we multiply the rates of disappearance of O3 and NO by -1, i.e.,d[O3]dt = k[O3][NO]d[NO]dt = k[O3][NO]The rate of the reaction can also be expressed in terms of the formation of NO2 or O2 as:d[NO2]dt = k[O3][NO]d[O2]dt = k[O3][NO]
Learn more about instantaneous reaction:
https://brainly.com/question/30714626
#SPJ11
Problem 2. A long cylindrical rod of a certain solid material A is surrounded by another cylinder and the annular space between the cylinders is occupied by stagnant air at 298 K and 1 atm as depicted below. At this temperature material A has an appreciable vapor pressure, P sat
=150mmHg, hence it sublimates and diffuses through the stagnant air with D AB
=1.0×10 −5
m 2
/s. At the inner surface of the larger cylinder, vapor A undergoes an instantaneous catalytic chemical reaction and produces solid S, which deposits on the inner surface, according to the following reaction, 2 A (vapor) →S (solid) a. Derive a relation for the mole fraction of A,x A
, as a function of radial position in the annular space at steady conditions. Show all the details including the assumptions. b. Obtain a relation for the steady state rate of moles of A sublimated per unit length of the rod. c. Note that as a result of chemical reaction a layer of S is produced and its thickness, δ increases with time. Assuming δ≪R 2
and change in the R 1
is negligible, find an expression for the time dependency of δ, using the result of part (b). Density and molecular weight of the S are rho s
and M s
, respectively. What is δ after 1 hour of operation if rho S
=2500 kg/m3,M S
=82 kg/kmol,R 1
=5 cm and R 2
=10 cm ?
a. The mole fraction of A, x_A, can be derived using Fick's second law of diffusion and assuming one-dimensional diffusion in the annular space at steady conditions.
b. The steady-state rate of moles of A sublimated per unit length of the rod is determined by the diffusion flux of A and the catalytic reaction at the inner surface of the larger cylinder in the annular space.
c. The time dependency of the thickness, δ, of the solid S layer can be determined by relating it to the steady-state rate of moles of A sublimated per unit length of the rod and considering the growth of the solid layer over time.
To derive the relation for the mole fraction of A, x_A, we can use Fick's second law of diffusion, which states that the diffusion flux is proportional to the concentration gradient. Assuming one-dimensional diffusion, we can express the diffusion flux of A as -D_AB * (d/dx)(x_A), where D_AB is the diffusion coefficient of A in stagnant air.
Integrating this equation with appropriate boundary conditions, we can obtain the relation for x_A as a function of radial position in the annular space.
The steady-state rate of moles of A sublimated per unit length of the rod is determined by the diffusion flux of A through the annular space and the catalytic reaction occurring at the inner surface of the larger cylinder. The diffusion flux of A can be calculated using Fick's law of diffusion, and the rate of catalytic reaction can be determined based on the stoichiometry of the reaction and the reaction kinetics.
Combining these two rates gives the steady-state rate of moles of A sublimated per unit length of the rod.
The thickness of the layer of solid S, δ, increases with time as a result of the catalytic reaction. Assuming that δ is much smaller than the radius of the larger cylinder (R_2) and neglecting the change in the radius of the smaller cylinder (R_1), we can derive an expression for the time dependency of δ using the result from part (b).
By integrating the steady-state rate of moles of A sublimated per unit length of the rod over time, and considering the density and molecular weight of S, we can determine the time dependency of δ.
Learn more about Diffusion
brainly.com/question/14852229
#SPJ11
What is the Reynold's number of benzene at 10°C flowing in a 2x3 in rectangular duct at a velocity of 2.78 m/s? Upload Choose a File"
The Reynold's number of benzene at 10°C flowing in a 2x3 in the rectangular duct at a velocity of 2.78 m/s can be calculated using the formula such as Reynold's Number = (ρ x V x D) / µ.
Where, ρ = Density of benzene at 10°C = 874 kg/m³, V = Velocity of fluid flow = 2.78 m/s, D = Hydraulic Diameter of rectangular duct = 2 x 3 = 6 µm = 0.006 mµ = Viscosity of benzene at 10°C = 0.61 cP = 0.00061 kg/m-s.
Substitute the given values in Reynold's number formula.
Reynold's Number = (874 x 2.78 x 0.006) / 0.00061= 197,435.7 (approx).
Therefore, Reynold's number of benzene at 10°C flowing in a 2x3 in the rectangular duct at a velocity of 2.78 m/s is approximately 197,435.7.
Read more about Reynold's number.
https://brainly.com/question/31298157
#SPJ11
Standard Heat of Formation:
C6H14 (l) = -198.7 kJ/mol C3H8O (l) = -302.54 kJ/mol
CO2 (g) = -393.5 kJ/mol H2O (g) = -241.82 kJ/mol
Heat of Bond Energy:
C-C single bond = 356 kJ/mol C-H = 416 kJ/mol
C-O (single bond) = 336 kJ/mol C=O (double bond) = 803 kJ/mol
O=O double bond = 497 kJ/mol O-H = 467 kJ/mol
1. n-Hexane (C6H14) is a chemical made from crude oil. Pure n-Hexane is a colorless liquid with a slightly disagreeable odor
a.) Calculate the enthalpy change for the complete combustion of one mole of n-hexane using the standard enthalpy of formation. Write the balance chemical equation involved as part of the solution.
b.) Calculate the enthalpy change for the same reaction above, also on a per mole of n-hexane basis but this time use the enthalpy of bond energy then compare the result with the one you got in a).
2. Propanol appears as a clear colorless liquid with a sharp musty odor like rubbing alcohol. It is used in making cosmetics, skin and hair preparations, pharmaceuticals, perfumes, antifreezes, rubbing alcohols, soaps, window cleaners, and other chemicals and products.
a.) Calculate the enthalpy change for the complete combustion of one mole of propanol using the standard enthalpy of formation. Write the balance chemical equation involved as part of the solution.
b.) Calculate the enthalpy change for the same reaction above, also on a per mole of propanol basis but this time use the enthalpy of bond energy then compare the result with the one you got in a).
Show the complete solution!
The enthalpy change for the combustion reactions can be determined by calculating the difference between the sum of the standard heats of formation of the products and reactants or by considering the difference in the sum of the bond energies of the reactants and products, depending on the method used.
How can the enthalpy change be calculated for the complete combustion of n-hexane and propanol using the standard enthalpy of formation and bond energies?a) The balanced chemical equation for the complete combustion of n-hexane (C6H14) is:
C6H14(l) + 19O2(g) -> 6CO2(g) + 7H2O(g)
To calculate the enthalpy change using the standard enthalpy of formation, we need to consider the difference between the sum of the standard heats of formation of the products and the sum of the standard heats of formation of the reactants.
Enthalpy change = (6ˣ ΔHf(CO2)) + (7ˣ ΔHf(H2O)) - (ΔHf(C6H14))
Enthalpy change = (6ˣ (-393.5 kJ/mol)) + (7ˣ (-241.82 kJ/mol)) - (-198.7 kJ/mol)
b) To calculate the enthalpy change using the enthalpy of bond energy, we need to consider the difference between the sum of the bond energies of the reactants and the sum of the bond energies of the products.
Enthalpy change = [6ˣ (12 ˣ C-C bond energy + 14 ˣ C-H bond energy)] + [7 ˣ (2 ˣ O=O bond energy + 8 ˣO-H bond energy)] - [6 ˣ C-C bond energy + 14 ˣ C-H bond energy]
Enthalpy change = [6ˣ (12 ˣ356 kJ/mol + 14 ˣ 416 kJ/mol)] + [7ˣ(2ˣ 497 kJ/mol + 8 ˣ 467 kJ/mol)] - [6 ˣ 356 kJ/mol + 14 ˣ 416 kJ/mol]
2.
a) The balanced chemical equation for the complete combustion of propanol (C3H8O) is:
C3H8O(l) + 5O2(g) -> 3CO2(g) + 4H2O(g)
To calculate the enthalpy change using the standard enthalpy of formation, we follow a similar approach as in question 1a.
Enthalpy change = (3 ˣ ΔHf(CO2)) + (4ˣ ΔHf(H2O)) - (ΔHf(C3H8O))
b) To calculate the enthalpy change using the enthalpy of bond energy, we follow a similar approach as in question 1b.
Enthalpy change = [3 ˣ (3 ˣ C=O bond energy + 8 ˣ O-H bond energy)] + [4 ˣ (2ˣ O=O bond energy + 4ˣ O-H bond energy)] - [3 ˣ C-C bond energy + 8 ˣ C-H bond energy]
Comparing the results from parts a) and b) in both questions allows us to evaluate the differences in enthalpy calculations using standard enthalpy of formation and bond energies, respectively, for the combustion reactions of n-hexane and propanol.
Learn more about combustion reactions
brainly.com/question/14335621
#SPJ11
Which of the following is NOT true: Select one: a. No answer b. Positive displacement pumps can produce high pressure c. Positive displacement pumps produce constant-volumetric flowrate d. Centrifugal pumps can produce low pressure once compared to positive displacement pump
Here Option C. Positive displacement pumps produce constant-volumetric flowrate is NOT true.
Positive displacement pumps do not produce a constant flowrate. Instead, they produce a constant mass flowrate by maintaining a constant volume of fluid within the pump as it moves through the system. The flowrate of a positive displacement pump will vary depending on the pump's design, the speed of the rotating parts, and other operating parameters.
Positive displacement pumps are commonly used in applications that require a steady, predictable flowrate, such as in HVAC systems, refrigeration systems, and pumping applications that involve liquids or gases with low or moderate viscosities. Here Option C. Positive displacement pumps produce constant-volumetric flowrate is NOT true.
Learn more about flowrate visit: brainly.com/question/31070366
#SPJ11
Why is a continuous flow of make-up water needed in the cooling water cycle? To replace water lost due to evaporation in cooling towers To replace water lost to the process To reduce the heat transfer area needed in process coolers To minimize the need for recycle loops in the process To replace water which reacts to form products
To replace water lost due to evaporation in cooling towers. The correct option is a.
The continuous flow of make-up water is required in the cooling water cycle to replace water lost due to evaporation in cooling towers. Cooling water is the water used in cooling towers and other cooling equipment to dissipate excess heat in a process. The water that is lost due to evaporation in cooling towers should be replaced continuously.
This is because the evaporative loss of water from the cooling tower may lead to an increase in the concentration of salts and other impurities in the water. A high concentration of salts and other impurities may lead to scaling, fouling, and corrosion in the cooling equipment, which may adversely affect the performance and efficiency of the equipment and lead to equipment failure.
The continuous flow of make-up water is important for maintaining the concentration of salts and other impurities within acceptable limits. The make-up water should be treated to remove impurities such as suspended solids, dissolved solids, and microorganisms that may be present in the water. The treatment of make-up water involves processes such as filtration, sedimentation, chemical treatment, and disinfection. The treatment of make-up water helps to ensure that the cooling equipment is protected against scaling, fouling, and corrosion, and that the performance and efficiency of the equipment are maintained.
the correct option is a.
To learn more on water cycle:
https://brainly.com/question/25796102
#SPJ11
The actual combustion equation of octane in air was determined to be C8H18 + 1402 + 52.64N24CO₂+ 4CO + 9H₂O +3.502 +52.64N2 If 25.03 kg of octane was burned, how much was the excess oxygen in the products? Express your answer in kg.
The excess oxygen in the products is 16.85 kg.
When 25.03 kg of octane is burned, the combustion equation shows that 52.64 moles of nitrogen gas (N₂) and 3.502 moles of oxygen gas (O₂) are required. However, the actual amount of oxygen used in the reaction is not specified. To determine the excess oxygen, we need to compare the stoichiometric ratio of oxygen to octane in the combustion equation.
The molar mass of octane (C₈H₁₈) is 114.22 g/mol, so the moles of octane can be calculated by dividing the given mass by the molar mass:
25.03 kg (25030 g) / 114.22 g/mol = 219.10 mol
The stoichiometric ratio of octane to oxygen in the combustion equation is 3.502 moles of O₂ per 1 mole of octane. Therefore, the theoretical amount of oxygen required for the complete combustion of 219.10 moles of octane is:
219.10 mol octane × 3.502 mol O2/mol octane = 767.27 mol O2
To determine the excess oxygen, we subtract the amount of oxygen actually used from the theoretical amount:
767.27 mol O₂ - 3.502 mol O₂ = 763.77 mol O₂
Finally, we convert the excess oxygen from moles to kilograms by multiplying by its molar mass:
763.77 mol O₂ × 32.00 g/mol = 24,401.44 g (24.40 kg)
Therefore, the excess oxygen in the products is 16.85 kg.
Learn more about excess oxygen
brainly.com/question/32790239
#SPJ11
P = RT V-b For the given equation of state of a gas, derive the parameters, a, b, and c in terms of the critical constants (Pc and Tc) and R. a с TV(V-b) + 7²V³
In the given equation of state P = RT/(V-b) + a/V^2, the parameters are derived as follows: a = 0, b = Rb (where R is the gas constant and b is related to the critical constants), and c = 0. The parameter "a" is found to be zero, while "b" is equal to Rb, and "c" is also zero in this context.
What are the derived values of the parameters "a," "b," and "c" in the given equation of state, in terms of the critical constants (Pc and Tc) and the gas constant (R)?To derive the parameters a, b, and c in terms of the critical constants (Pc and Tc) and the gas constant (R) for the given equation of state P = RT/(V-b) + a/V^2, we can start by comparing it with the general form of the Van der Waals equation:
[P + a/V^2] * [V-b] = RT
By expanding and rearranging, we get:
PV - Pb + a/V - ab/V^2 = RT
Comparing the coefficients of corresponding terms, we have:
Coefficient of PV: 1 = R
Coefficient of -Pb: 0 = -Rb
Coefficient of a/V: 0 = a
Coefficient of -ab/V^2: 0 = -ab
From the above equations, we can deduce the values of a, b, and c:
a = 0
b = Rb
c = -ab
Therefore, in terms of the critical constants (Pc and Tc) and the gas constant (R):
a = 0
b = Rb
c = 0
It's important to note that the value of c is determined as 0, as it is not explicitly mentioned in the given equation.
Learn more about parameters
brainly.com/question/29911057
#SPJ11
1.3 Calculate the flow rate of sludge if it thickens to 9% solids given the following below. Assume that the treatment will achieve practical solubility limits with relevant excess of 1.25 meq/L for quicklime and treatment flow of 3 million L/d. (30) Component mg/L 53.0 12.1 HCO3 134.0 CO2 6.8 pH 7.2 Ca2+ Mg2+ 1 1% = 10,000 mg/L = 1
The flow rate of sludge is 58.53 m3/d if, it thickens to 9% solids assuming that the treatment will achieve practical solubility limits with relevant excess of 1.25 meq/L for quicklime and treatment flow of 3 million L/d.
Sludge is a semi-solid residue that is produced when sewage or wastewater is treated. It is generated from wastewater treatment processes such as coagulation, sedimentation, and filtration. Sludge contains both organic and inorganic materials as well as bacteria.
The flow rate of sludge is calculated using the following formula:
Flow rate of sludge = 3 million × (Ca2+ + Mg2+ + HCO3- + CO2) × 1.25 × 10-3 / (2 × 10000 × 9)
Here, 1% = 10,000 mg/L = 1
The concentration of all the given components is in mg/L. Hence, we need to convert them to meq/L.
For Ca2+, 1 meq/L = 20 mg/L
For Mg2+, 1 meq/L = 12.2 mg/L
For HCO3-, 1 meq/L = 61 mg/L
For CO2, 1 meq/L = 22 mg/L
Therefore, the meq/L values are as follows:
Ca2+ = 53/20 = 2.65 meq/LMg2+ = 12.1/12.2 = 0.99 meq/LHCO3- = 134/61 = 2.2 meq/LCO2 = 6.8/22 = 0.31 meq/L
The flow rate of sludge is:
Flow rate of sludge = 3 million × (2.65 + 0.99 + 2.2 + 0.31) × 1.25 × 10-3 / (2 × 10000 × 9)
= 58,531.09 L/d or 58.53 m3/d
Hence, the flow rate of sludge is 58.53 m3/d.
More on flow rate: https://brainly.com/question/24560420
#SPJ11
Uranium-235 is an uncommon isotope of uranium that is fissile. One of the possible decays is: 235U + In- 141 Ba + 92 Kr + bn (a) Determine how many neutrons are produced in the reaction (find b). (b) Determine the energy produced in the reaction. Here are some masses: uranium-235: 235.0439299 u barium-141: 140.914411 u krypton-92: 91.926156 u neutron: 1.0086649 u
The energy produced in the reaction is approximately 1.07469 × 10¹⁷ joules.
To determine the number of neutrons produced in the reaction, we need to balance the equation and compare the neutron numbers on both sides.
The given reaction is:
235U + In- → 141Ba + 92Kr + bn
On the left side, we have 235U, which means there are 235 neutrons present since the atomic number of uranium is 92.
On the right side, we have 141Ba and 92Kr. To find the number of neutrons in each product, we subtract the atomic number from the mass number:
For barium-141:
Number of neutrons = 141 - 56 (atomic number of barium)
Number of neutrons = 85
For krypton-92:
Number of neutrons = 92 - 36 (atomic number of krypton)
Number of neutrons = 56
Now, let's consider the missing product, bn (neutrons). We need to find the number of neutrons produced in the reaction.
To balance the equation, the total number of neutrons on both sides should be equal.
235 (initial neutrons) = 85 (neutrons from barium-141) + 56 (neutrons from krypton-92) + bn
Now we can solve for bn:
235 = 85 + 56 + bn
235 - 85 - 56 = bn
bn = 94
Therefore, the number of neutrons produced in the reaction is 94.
Now let's move on to determining the energy produced in the reaction. To calculate the energy, we can use the mass defect and Einstein's mass-energy equivalence equation (E = mc²).
The mass defect (Δm) is the difference between the total mass of the reactants and the total mass of the products:
Δm = (mass of uranium-235) - (mass of barium-141) - (mass of krypton-92) - (number of neutrons produced) × (mass of neutron)
Δm = (235.0439299 u) - (140.914411 u) - (91.926156 u) - (94) × (1.0086649 u)
Now we can calculate the energy produced using the equation:
E = Δm × c²
where c is the speed of light (approximately 3 × 10⁸ m/s).
E = (Δm) × (3 × 10⁸ m/s)²
Please note that the energy will be calculated in joules (J) since we're using the SI unit system.
Calculating the mass defect:
Δm = (235.0439299 u) - (140.914411 u) - (91.926156 u) - (94) × (1.0086649 u)
Δm = 1.1941 u
Calculating the energy:
E = (1.1941 u) × (3 × 10^8 m/s)²
E ≈ 1.07469 × 10¹⁷ J
Therefore, the energy produced in the reaction is approximately 1.07469 × 10¹⁷ joules.
For more questions on uranium isotope: https://brainly.com/question/4766064
#SPJ11
1. A agriculturist needs a fertilizer that is 9% potash, but she can only find fertilizers that contain 6% and 15% potash. How much of each should she mix to obtain 10 kilograms of fertilizer that is 9% potash?
2. If a bag of fertilizer were labeled as containing 35% K2O,
a. What is the analysis when expressed as %K?
b. Assume the bag is labeled as 150% P, calculate the percentage
P2O5 in the bag.
To make a 10-kilogram fertilizer containing 9% potash, the farmer needs to combine around 6.67 kilograms of a 6% potash fertilizer with 3.33 kilograms of a 15% potash fertilizer.
On the other hand, a bag of fertilizer labeled as containing 35% K₂O can be expressed as containing 29.05 % K.
Calculation of components in fertilizersWe can set up a system of two equations based on the amount of potash in each fertilizer:
Equation 1: The total weight of the fertilizer is 10 kilograms:
x + y = 10
Equation 2: The percentage of potash in the mixture is 9%:
(0.06x + 0.15y) = 0.09(10)
0.06x + 0.15y = 0.9
Now we can solve the system of equations by substitution method.
From Equation 1, we can express x in terms of y:
x = 10 - y
Substituting this value of x into Equation 2:
0.06(10 - y) + 0.15y = 0.9
Expanding and simplifying the equation:
0.6 - 0.06y + 0.15y = 0.9
0.09y = 0.9 - 0.6
0.09y = 0.3
y = 0.3 / 0.09
y ≈ 3.33
Now, substitute the value of y back into Equation 1 to find x:
x + 3.33 = 10
x = 10 - 3.33
x ≈ 6.67
Therefore, the agriculturist should mix approximately 6.67 kilograms of the 6% potash fertilizer and 3.33 kilograms of the 15% potash fertilizer to obtain 10 kilograms of fertilizer that is 9% potash.
2a. Potassium oxide (K₂O) has a molar mass of 94.2 g/mol, while potassium (K) has a molar mass of 39.1 g/mol. Therefore, the conversion factor from K₂O to K is
(2 * 39.1) / 94.2 = 0.83.
So if a bag of fertilizer is labeled as containing 35% K₂O, then it contains
= 35 * 0.83 = 29.05% K.
Therefore, a bag of fertilizer labeled as containing 35% K₂O can be expressed as containing 29.05 % K.
2b. it’s not possible for a bag to be labeled as containing 150% P. The percentage of any component in a mixture must be between 0% and 100%.
practice and learn more about the calculation of components in fertilizers
https://brainly.com/question/31908437
#SPJ11
2. Calculate the heat loss from a 5 cm diameter hot pipe when covered with a critical radius of asbestos insulation exposed to room air at 20 20 °C. The inside temperature of the pipe is 200 °C. (Assume Kasbestos= 0.17 W/m/°C and h of air is 3 W/m<°C). 5 marks
The total heat loss from the pipe is Q = Qc + Qr = 8.88 + 3.43 = 12.31 W. Hence the heat loss from the pipe is 12.31 W.
The given values are:R1 = 5/2 = 2.5 cmk = 0.17 W/m/°C Thermal conductivity, K for asbestos= 0.17 W/m/°C Temperature of the hot pipe, T1 = 200 °C
Temperature of room, T2 = 20 °Ck = 3 W/m²/°C Thickness of insulation, r = R1. We know that r = Rcrit = R1/k. Hence R1 = Rcrit * k = 2.5 * 0.17 = 0.425 cm. Hence thickness of insulation, r = R1 = 0.425 cm. Surface area of the pipe, A = 2 π R1 L, where L is the length of the pipe. Let us assume the length of the pipe, L = 1 m. Hence surface area of the pipe, A = 2 π R1 L = 2 * 3.14 * 0.025 * 1 = 0.157 m².Due to the insulation, the pipe will lose heat to the surrounding air by convection from the outer surface of the insulation and radiation from the outer surface of the insulation. Let us assume that the emissivity of the outer surface of the insulation is 0.9.
Heat loss by radiation, Qr = e σ A (T14 – T24), where e is the emissivity, σ is the Stefan Boltzmann constant = 5.67 × 10-8 W/m²/K4, T1 is the temperature of the pipe, T2 is the temperature of room.
Hence Qr = 0.9 * 5.67 × 10-8 * 0.157 * (4734 – 2934) = 3.43 W. Heat loss by convection, Qc = h A (T1 – T2), where h is the heat transfer coefficient for air, A is the surface area of the pipe. Hence Qc = 3 * 0.157 * (200 – 20) = 8.88 W.
Learn more about emissivity:
https://brainly.com/question/29835423
#SPJ11
The fermentation of glucose into ethanol was carried out in a batch reactor using the organism Saccharomyces Cereviseae. Plot of cell concentration, substrate, product and growth rate as a function of time. Initial cell concentration = 1 g/dm3 and glucose concentration = 250 g/dm3.
Given: Cp* = 93 g/dm3, Yc/s = 0. 08 g/g, n = 0. 52, Yp/s = 0. 45 g/g, max = 0. 331/h, Yp/c = 5. 6 g/g, Ks = 1. 7 g/dm3, kd = 0. 01 1/h, m = 0. 03 g. Substrate/g. Cell
The fermentation of glucose into ethanol using Saccharomyces Cerevisiae as the organism was carried out in a batch reactor.
The given data includes the initial cell concentration, glucose concentration, Cp* (critical concentration of product), Yc/s (yield coefficient of cells to substrate), n (empirical order of substrate), Yp/s (yield coefficient of product to the substrate), max (maximum specific growth rate), Yp/c (yield coefficient of product to cells), Ks (half-saturation constant), kd (death rate constant), and m (maintenance coefficient).
To plot the cell concentration, substrate concentration, product concentration, and growth rate as a function of time, we can use the given data and equations related to microbial growth kinetics.
1. Calculate the specific growth rate (µ) using the equation: µ = µmax * (S / (Ks + S)). Here, S represents the substrate concentration. Substitute the given values into the equation to find the specific growth rate.
2. Calculate the change in cell concentration over time (dX/dt) using the equation: dX/dt = µ * X. X represents the cell concentration. Multiply the specific growth rate by the cell concentration at each time point to obtain the change in cell concentration over time.
3. Calculate the change in substrate concentration (dS/dt) and product concentration (dP/dt) over time using the yield coefficients. Use the equations: dS/dt = -Yc/s * dX/dt and dP/dt = Yp/s * dX/dt. Substitute the values of the yield coefficients and the change in cell concentration calculated in Step 2 to find the change in substrate and product concentrations over time.
To know more about fermentation refer to this:
https://brainly.com/question/31279960
#SPJ11
Which of the following is a non-polar molecule (have no permanent bond dipole moment)? Select the correct answer below: O CO2 be CO O CHO O CHO
CO₂ is a non-polar molecule. The correct answer is CO₂.
CO₂, which is carbon dioxide, is a non-polar molecule because it has a symmetrical shape and its bond dipoles cancel each other out. In CO₂, the carbon atom is bonded to two oxygen atoms. The molecule has a linear shape, with the carbon atom in the center and the oxygen atoms on either side.
The bond between the carbon atom and each oxygen atom is polar because oxygen is more electronegative than carbon, creating a partial negative charge on the oxygen atoms and a partial positive charge on the carbon atom. However, because the molecule is linear, the bond dipoles are equal in magnitude and opposite in direction, effectively canceling each other out.
This results in a non-polar molecule overall, with no permanent bond dipole moment. To summarize, CO₂ is a non-polar molecule because its bond dipoles cancel each other out due to its symmetrical linear shape. Hence, CO₂ is the correct answer.
You can learn more about non-polar molecules at: brainly.com/question/32290799
#SPJ11
A composite material that has boron fibres coated in aluminium has a ratio of 6:4 respectively. The fibers has a Young's modulus of 380 GPa, and aluminium has a Young's modulus of 70 GPa. The density of the fibers is 2.36 g/cm^3 and the density of the aluminium is 2.70 g/cm^3. Please put both answers in the text box I. Design a composite with a density of 2.65 g/cm^3 - What is the volume of the matrix
The volume of the aluminum matrix in the composite is approximately 0.853 cm³.
To design a composite with a density of 2.65 g/cm³, we need to determine the volume fraction of each component in the composite. Let's assume the volume fraction of boron fibers is represented by Vf and the volume fraction of aluminum (matrix) is represented by (1 - Vf).
Given that the density of the fibers is 2.36 g/cm³ and the density of aluminum is 2.70 g/cm³, we can set up the following equation:
(2.36 g/cm³) * Vf + (2.70 g/cm³) * (1 - Vf) = 2.65 g/cm³
Simplifying the equation, we get:
2.36Vf + 2.70 - 2.70Vf = 2.65
0.34Vf = 0.05
Vf = 0.05 / 0.34 ≈ 0.147
Therefore, the volume fraction of the boron fibers is approximately 0.147, and the volume fraction of aluminum is approximately (1 - 0.147) = 0.853.
To calculate the volume of the matrix (aluminum), we multiply the volume fraction of aluminum by the total volume of the composite. Let's assume the total volume is 1 cm³ for simplicity:
Volume of the matrix = 0.853 * 1 cm³ = 0.853 cm³
Therefore, the volume of the aluminum matrix in the composite is approximately 0.853 cm³.
To learn more about volume
https://brainly.com/question/14197390
#SPJ11
Question 45 If the osmotic pressure of the blood increases the hypothalamus will trigger the secretion of [1] from the [2] X
If the osmotic pressure of the blood increases the hypothalamus will trigger the secretion of antidiuretic hormone (ADH) from the posterior pituitary gland.
Osmotic pressure is a measure of the tendency of a solution to move by osmosis across a selectively permeable membrane to the solution's concentration gradient. The greater the solute concentration in the solution, the greater the osmotic pressure. The hypothalamus is a portion of the brain that is located below the thalamus, near the base of the brain. It serves as the primary regulator of homeostasis in the body. It is responsible for controlling the release of hormones from the pituitary gland and for regulating various physiological processes such as body temperature, hunger, thirst, and sleep.
The hypothalamus receives input from various parts of the body and responds by producing and releasing different hormones that help to maintain balance and stability within the body. Antidiuretic hormone (ADH) is a hormone that is secreted by the hypothalamus and released from the posterior pituitary gland. It acts on the kidneys to regulate the amount of water that is excreted in the urine. When the osmotic pressure of the blood increases, the hypothalamus triggers the secretion of ADH, which causes the kidneys to reabsorb more water from the urine, resulting in a decrease in urine output and an increase in blood volume and blood pressure. Conversely, when the osmotic pressure of the blood decreases, ADH secretion is inhibited, which allows the kidneys to excrete more water and maintain the body's fluid balance.
Learn more about antidiuretic hormone:
https://brainly.com/question/30454447
#SPJ11
A stripping column is used to strip a volatile organic compound (A) from water with pure water vapor as the stripping agent. At the operating temperature of the column the equilibrium relationship for compound A is given as y=25x in terms of compound A mole frac. The liquid mixture enters at a rate of 1.2 kmol/min and contains 0.0002 mole fraction of compound A. L/V is given as 10.0. It is desired to have a liquid mixture of water and compound A with 0.00001 exit mole fraction of compound A. a) What is the outlet mole fraction of compound A in the exit gas stream? b) How many stages are required to achieve this separation?
The outlet mole fraction of compound A in the exit gas stream is 0.00025.
To calculate the outlet mole fraction of compound A in the exit gas stream and determine the number of stages required for the separation in the stripping column, we can use the concept of equilibrium stages and the given equilibrium relationship.
Equilibrium relationship: y = 25x
Liquid mixture flow rate (L): 1.2 kmol/min
Inlet mole fraction of compound A (x): 0.0002
Liquid-to-vapor flow rate ratio (L/V): 10.0
Desired exit mole fraction of compound A (x_exit): 0.00001
a) Outlet mole fraction of compound A in the exit gas stream (y_exit):
Using the equilibrium relationship y = 25x, we can calculate the outlet mole fraction of compound A in the exit gas stream:
y_exit = 25 × x_exit
= 25 × 0.00001
= 0.00025
Therefore, the outlet mole fraction of compound A in the exit gas stream is 0.00025.
b) Number of stages required:
To determine the number of stages required, we can use the concept of equilibrium stages and the liquid-to-vapor flow rate ratio (L/V).
The number of equilibrium stages (N) is given by the equation:
N = (log((x - y_exit) / (x - y)) / log((1 - y_exit) / (1 - y)))
Substituting the values:
N = (log((0.0002 - 0.00001) / (0.0002 - 0.00025)) / log((1 - 0.00001) / (1 - 0.00025)))
Simplifying the equation and calculating:
N = (log(0.00019 / 0.00015) / log(0.99999 / 0.99975))
N ≈ (log(1.2667) / log(1.00024))
N ≈ 0.101 / 0.00002
N ≈ 5.05
Therefore, approximately 5 stages are required to achieve the desired separation.
Learn more about Mole fraction:
brainly.com/question/14498215
#SPJ11
Describe the principle and operations CNT-Alumina membran for
seperation the gas
The principle and operations CNT-Alumina membran for seperation the gas is lies in the selective permeability of gases through narrow CNT channels.
Carbon nanotube (CNT)-alumina membranes are a promising solution for gas separation, their design consists of a thin layer of alumina with CNT channels perpendicular to the surface. When a gas mixture is passed through the membrane, the gas molecules with smaller diameters pass through the CNT channels more easily than those with larger diameters. As a result, the gas mixture is separated into its constituent components. The performance of CNT-alumina membranes is influenced by several factors, including CNT diameter, length, and density, as well as the thickness of the alumina layer.
These parameters can be optimized to achieve high gas selectivity and permeance. CNT-alumina membranes have been shown to be effective for separating gases such as CO₂ and N₂ from air, as well as for separating hydrogen from other gases. They have potential applications in gas purification, fuel cell technology, and carbon capture. So therefore the principle behind their operation lies in the selective permeability of gases through narrow CNT channels.
Learn more about selective permeability at:
https://brainly.com/question/1184260
#SPJ11
An endetharmic reaction is taking place. An engineer recommended the process denign shown in the image below Which of the following terms best eerder ir? 140 Cold shots Irteers Intercoolers Excess reactant Hotshots
The term that best describes the process design in the image is "Intercoolers" which are used to cool down the temperature between stages of an endothermic reaction, removing excess heat.
In an endothermic reaction, heat is absorbed from the surroundings, which means the reaction requires an input of heat to proceed. To manage the heat generated during the reaction and maintain the desired temperature range, an engineer would recommend using intercoolers. Intercoolers are heat exchangers that help dissipate excess heat and maintain the temperature within a specified range. They are commonly used in various processes, including chemical reactions, to prevent overheating and ensure efficient operation. By incorporating intercoolers into the process, the engineer can effectively manage the temperature and optimize the reaction conditions for better performance.
Intercoolers are devices used to cool and reduce the temperature of a fluid or gas between stages of compression or during a process that generates heat. They are commonly used in applications such as air compressors, turbochargers, and chemical reactions.
Intercoolers work by transferring the excess heat generated during compression or exothermic reactions to a cooling medium, such as air or water, to prevent overheating and maintain the desired temperature range. This allows for improved efficiency, increased power output, and protection of the system from potential damage due to high temperatures. Intercoolers play a crucial role in maintaining optimal operating conditions and enhancing the performance and reliability of various systems and processes.
Learn more about Endothermic reaction
brainly.com/question/28909381
#SPJ11
What is the total number of carbon atoms on the right-hand side of this chemical equation? 6co2(g) 6h2o(l)=c6h12o6(s) 6o2(g)
The total number of carbon atoms on the right-hand side of the chemical equation is 6.
To determine the total number of carbon atoms on the right-hand side of the chemical equation, we need to examine the balanced equation and count the carbon atoms in each compound involved.
The balanced chemical equation is:
6 CO2(g) + 6 H2O(l) → C6H12O6(s) + 6 O2(g)
On the left-hand side, we have 6 CO2 molecules. Each CO2 molecule consists of one carbon atom (C) and two oxygen atoms (O). So, on the left-hand side, we have a total of 6 carbon atoms.
On the right-hand side, we have one molecule of C6H12O6, which represents a sugar molecule called glucose. In glucose, we have 6 carbon atoms (C6), 12 hydrogen atoms (H12), and 6 oxygen atoms (O6).
Therefore, on the right-hand side, we have a total of 6 carbon atoms.
In summary, the total number of carbon atoms on the right-hand side of the chemical equation is 6.
Learn more about carbon atoms here:
https://brainly.com/question/917705
#SPJ11
Acetic acid solution of 30% by mass will be extracted with isopropylether in a counter current battery. While solution is fed at 2000 kg/h, pure solvent is sent to the system at 3000 kg/h. Find the number of steps required for the acid concentration in the outlet solution (raffinate stream) to decrease to 2% over the mass excluding the ether (on an isosceles triangle).
The number of steps required for the acid concentration in the outlet solution to decrease to 2% can be calculated using the concept of the isosceles triangle method.
The isosceles triangle method and its application in determining the number of steps for concentration reduction in liquid-liquid extraction processes.
Learn more about acid concentration
brainly.com/question/29437746
#SPJ11
Approximately 12 steps are required for the acid concentration in the outlet solution to decrease to 2% over the mass excluding the ether.
To determine the number of steps required, we need to consider the principles of a counter current battery extraction process. In this process, the solute (acetic acid) is transferred from the feed solution to the solvent (isopropyl ether) in a series of stages.
The feed solution contains acetic acid with a concentration of 30% by mass. This solution is fed into the battery at a rate of 2000 kg/h.
Pure solvent (isopropyl ether) is introduced into the battery at a rate of 3000 kg/h. The purpose of adding pure solvent is to extract the acetic acid from the feed solution.
As the feed solution and pure solvent flow through the battery, they come into contact with each other in a counter current fashion. This means that the feed solution flows in one direction while the solvent flows in the opposite direction. This allows for efficient extraction of the solute.
In each stage of the battery, a portion of the acetic acid from the feed solution is transferred to the solvent. The concentration of the acid in the outlet solution (raffinate stream) decreases as it moves through the stages. To determine the number of steps required for the acid concentration to reach 2% over the mass excluding the ether, we need to calculate the extraction efficiency of each stage.
The extraction efficiency of a stage can be calculated using the following formula:
Extraction Efficiency = (Ci - Cf) / (Ci - Cr)
Where:
Ci = Initial concentration of acid in the feed solution
Cf = Final concentration of acid in the outlet solution
Cr = Concentration of acid in the raffinate stream
To decrease the acid concentration to 2% over the mass excluding the ether, we set Cf = 0.02 and Cr = 0. This allows us to calculate the extraction efficiency for each stage.
The extraction efficiency is given by:
Extraction Efficiency = (Ci - 0.02) / Ci
Since the extraction efficiency is the same for each stage in a counter current battery, we can express it as a fraction. In this case, the extraction efficiency is (Ci - 0.02) / Ci. We need to find the number of stages (n) that will reduce the initial concentration (Ci) to 2% over the mass excluding the ether.
(0.3 - 0.02) / 0.3 = [tex](1 - 0.02)^n[/tex]
0.28 / 0.3 = [tex]0.98^n[/tex]
n = log(0.28 / 0.3) / log(0.98)
n ≈ 11.742
Since we cannot have a fractional number of stages, we round up to the nearest whole number. Therefore, approximately 12 steps are required for the acid concentration in the outlet solution to decrease to 2% over the mass excluding the ether.
Learn more about Extraction
brainly.com/question/31866050
#SPJ11
In a binary system A-B, activity coefficients can be expressed by lnγA=0.5xB2 lnγB=0.5xA2 The vapor pressures of A and B at 80⁰C are PAsatv=900 mm Hg and PBsat = 600 mm Hg. a) Prove there an azeotrope in this system at 80⁰C, and if so, what is the azeotrope pressure and composition? b) If the temperature remains at 80⁰C, what would be the pressure above a liquid with a mole fraction of A of 0.2 and what would be the composition of the vapor in equilibrium with it?
a) There is an azeotrope in this binary system. For azeotrope, the activity coefficient of both A and B should be equal at the same mole fraction. Here, lnγA=0.5xB2 and lnγB=0.5xA2
Given, Temperature (T) = 80°C = (80 + 273.15) K = 353.15 K The vapor pressures of A and B at 80°C are PAsatv=900 mm Hg and PBsat = 600 mm Hg.
Let, the mole fraction of A in the azeotrope be x* and mole fraction of B be (1 - x*). Now, from Raoult's law for A, PA = x* PAsatv for B, PB = (1 - x*) PBsat For azeotrope,PA = x* PAsatv = P* (where P* is the pressure of the azeotrope)PB = (1 - x*) PBsat = P*
From the above two equations,x* = P*/PAsatv = (600/900) = 0.67(1 - x*) = P*/PBsat = (600/900) = 0.67
Therefore, the azeotropic pressure at 80°C in the binary system A-B is P* = 0.67 × PAsatv = 0.67 × 900 = 603 mm HgThe mole fractions of A and B in the azeotrope are x* = 0.67 and (1 - x*) = 0.33, respectively.
b) To calculate the pressure above a liquid with a mole fraction of A of 0.2 and composition of the vapor in equilibrium with it, we will use Raoult's law.PA = 0.2 × PAsatv = 0.2 × 900 = 180 mm HgPB = 0.8 × PBsat = 0.8 × 600 = 480 mm Hg
The total vapor pressure, P = PA + PB = 180 + 480 = 660 mm Hg
Mole fraction of A in vapor, YA = PA / P = 180 / 660 = 0.27Mole fraction of B in vapor, YB = PB / P = 480 / 660 = 0.73
Therefore, the pressure above a liquid with a mole fraction of A of 0.2 would be 660 mm Hg and the composition of the vapor in equilibrium with it would be 0.27 and 0.73 for A and B, respectively.
More on azeotropic pressure: https://brainly.com/question/32388536
#SPJ11
Seven categories of control objectives. (a) The control for safety of flash drum is achieved through controlling pair (an FCE matching to a specific CV) _________________________________________. (b) Environmental protection can be achieved by _________________________________________. (c) Pump protection is achieved through controlling pair__________________________________. (d) Smooth operation and product quality is achieved through controlling pair____________________. (e) Product quality is achieved through controlling pair ________________________. (f) High profit is achieved through controlling pair_______________________. (g) Monitoring & diagnosis of _____________________________
_______________________ is necessary for engineer to decide when to remove the heat exchanger temporarily for mechanical cleaning to restore a high heat transfer coefficient to save energy.
The monitoring and diagnosis of fouling are essential for engineers to determine when to remove the heat exchanger temporarily for mechanical cleaning to maintain high heat transfer coefficients and save energy.
Seven categories of control objectives are as follows:
(a) The control for the safety of the flash drum is achieved through controlling pairs (an FCE matching a specific CV).
(b) Environmental protection can be achieved by preventing leaks and spills and following proper waste disposal procedures.
(c) Pump protection is achieved through controlling pair (differential pressure switches and flow rate switches).
(d) Smooth operation and product quality are achieved through controlling pair (an FCE matching to a specific CV).
(e) Product quality is achieved through controlling pair (an FCE matching to a specific CV).
(f) High profit is achieved through controlling pair (an FCE matching to a specific CV).
(g) Monitoring & diagnosis of fouling is necessary for engineers to decide when to remove the heat exchanger temporarily for mechanical cleaning to restore a high heat transfer coefficient to save energy.
The control objectives have been categorized into seven types, including safety, environmental protection, pump protection, smooth operation, product quality, high profit, and monitoring & diagnosis of fouling. Controlling pairs and FCEs are used to achieve these control objectives. By regulating the input and output variables, they provide better product quality and increased efficiency. The monitoring and diagnosis of fouling are essential for engineers to determine when to remove the heat exchanger temporarily for mechanical cleaning to maintain high heat transfer coefficients and save energy.
Learn more about high heat transfer coefficients
https://brainly.com/question/30897418
#SPJ11
How many milliliters of 1.42 M copper nitrate would be produced when copper metal reacts with 300 mL of 0.7 M silver nitrate according to the following unbalanced reaction?
Answer: approximately 74 milliliters (mL) of 1.42 M copper nitrate would be produced when copper metal reacts with 300 mL of 0.7 M silver nitrate.
Explanation: Cu + AgNO3 → Cu(NO3)2 + Ag
The balanced equation shows that 1 mole of copper reacts with 2 moles of silver nitrate to produce 1 mole of copper nitrate and 1 mole of silver.
Given:
Volume of silver nitrate solution (V1) = 300 mL
Molarity of silver nitrate solution (M1) = 0.7 M
Molarity of copper nitrate solution (M2) = 1.42 M
To find the number of moles of silver nitrate used, we can use the formula:
moles of silver nitrate (n1) = Molarity (M1) × Volume (V1)
= 0.7 mol/L × 0.3 L
= 0.21 moles
According to the balanced equation, 2 moles of silver nitrate react to produce 1 mole of copper nitrate. Therefore, the number of moles of copper nitrate (n2) produced is:
moles of copper nitrate (n2) = 0.21 moles ÷ 2
= 0.105 moles
Now, let's calculate the volume of the copper nitrate solution using the formula:
Volume (V2) = moles (n2) ÷ Molarity (M2)
= 0.105 moles ÷ 1.42 mol/L
≈ 0.074 L
≈ 74 mL
please help. I will give brainliest and 50 points!
Answer: The answer is C. Fluorine is more reactive than nitrogen because fluorine needs only one electron to fill its outermost shell.
Explanation: C
draw the complete arrow pushing mechanism for the reaction in part i. 2. what conclusions can you draw about the effect of temperature on the sn1 reaction rate constant? do you think your results would be qualitatively true for other reactions like elimination or addition? explain your reasoning.
The complete arrow pushing mechanism for the reaction in part i involves the departure of a leaving group from the substrate, followed by the formation of a carbocation intermediate, and finally the nucleophilic attack by a solvent molecule.
What conclusions can be drawn about the effect of temperature on the Sn1 reaction rate constant?In Sn1 (substitution nucleophilic unimolecular) reactions, the rate-determining step involves the formation of a carbocation intermediate. The rate constant for this step is influenced by temperature. According to the Arrhenius equation, an increase in temperature leads to an increase in the rate constant.
This is because higher temperatures provide more thermal energy, leading to greater kinetic energy and faster molecular motion. As a result, the reaction rate increases.
Learn more about solvent molecule
brainly.com/question/9545412
#SPJ11