It can be understood that as heat energy is transferred to the water, its entropy increases. This is due to the fact that the water molecules become more disordered as they gain energy.
In order to find the entropy change that water undergoes during the process, we can use the following steps:
Step 1: First, we need to find the amount of heat energy that is required to raise the temperature of the water from 20°C to 100°C using the formula Q = mcΔT, where Q is the amount of heat energy required, m is the mass of water (1.8 kg), c is the specific heat capacity of water (4.18 J/g°C), and ΔT is the change in temperature (100°C - 20°C = 80°C).So, Q = (1.8 kg)(4.18 J/g°C)(80°C) = 603.36 kJ
Step 2: Next, we need to find the amount of heat energy that is required to boil the water at 100°C using the formula Q = mL, where Q is the amount of heat energy required, m is the mass of water (1.8 kg), and L is the specific heat of vaporization of water (2260 J/g).So, Q = (1.8 kg)(2260 J/g) = 4068 kJ
Step 3: The total amount of heat energy required is the sum of the two values we just calculated:Q = 603.36 kJ + 4068 kJ = 4671.36 kJ
Step 4: The entropy change that the water undergoes during this process can be found using the formula ΔS = Q/T, where ΔS is the entropy change, Q is the amount of heat energy required (4671.36 kJ), and T is the temperature (in Kelvin) at which the heat energy is transferred.For this process, the temperature remains constant at 100oC until all the water has been converted to steam. Therefore, we can assume that the heat energy is transferred at a constant temperature of 100°C or 373 K.So, ΔS = (4671.36 kJ)/(373 K) = 12.51 kJ/K
Step 5: Therefore, the entropy change that the water undergoes during the process is 12.51 kJ/K.
It can be understood that as heat energy is transferred to the water, its entropy increases. This is due to the fact that the water molecules become more disordered as they gain energy. When the water boils and turns into steam, the entropy increases even more, since the steam molecules are even more disordered than the liquid water molecules. The overall result is a large increase in entropy, which is consistent with the second law of thermodynamics.
To know more about heat energy visit:
brainly.com/question/29210982
#SPJ11
A typical region of interstellar space may contain 106
atoms per cubic meter (primarily hydrogen) at a temperature of
-173.15 °C. What is the pressure of this gas?
The pressure of gas in a typical region of interstellar space containing 106 atoms per cubic meter (mainly hydrogen) at a temperature of -173.15 °C is 0.26 femtometer-2.
What is pressure? Pressure is defined as the amount of force exerted per unit area. The following equation defines pressure in physics: P = F / A where P represents pressure, F represents force, and A represents area. The given equation may be utilized to solve the present problem. How to solve this problem? The ideal gas law can be used to solve this problem: PV = nRT where P is the pressure, V is the volume, n is the number of moles, R is the universal gas constant, and T is the temperature.
The density can be used to convert moles to volume (mass / volume), and since the gas in this example is hydrogen, its molar mass is 2.016 grams per mole.
We can use the following equation for the density: p = m / V = nM / V where p is the density, m is the mass, M is the molar mass, and V is the volume.
To know more about pressure visit:
https://brainly.com/question/30673967
#SPJ11
3. A proton is located at A, 1.0 m from a fixed +2.2 x 10-6 C charge. The electric field is 1977.8 N/C across A [5 marks total] to B. B proton 2.2x10-6 C +1.0 m -10m a) What is the change in potential energy of the proton as it moves from A to B? [2] b) If the proton started from rest at A, what would be its speed at B? [
a) The change in potential energy of the proton as it moves from A to B is 2.424 × 10⁻¹⁵ J ; b) The speed of the proton at B is 1.75 × 10⁵ m/s.
a) At point A, the proton is located at a distance of 1 meter from the fixed +2.2 x 10⁻⁶ C charge.
Therefore, the electric field vector at A is:
E = kq/r² = (9 × 10⁹ N·m²/C²)(2.2 × 10⁻⁶ C)/(1 m)²
= 1.98 × 10³ N/C
The potential difference between points A and B is:
∆V = Vb − Va
= − [tex]∫a^b E · ds[/tex]
[tex]= − E ∫a^b ds[/tex]
= − E (b − a)
= − (1977.8 N/C)(10 m − 1 m)
= − 17780.2 V
The change in potential energy of the proton as it moves from A to B is:
ΔU = q∆V = (1.6 × 10⁻¹⁹ C)(− 17780.2 V)
= − 2.424 × 10⁻¹⁵ J
b) The potential energy of the proton at B is:
U = kqQ/r
= (9 × 10⁹ N·m²/C²)(2.2 × 10⁻⁶ C)(1.6 × 10⁻¹⁹ C)/(10 m)
= 3.168 × 10⁻¹⁴ J
The total mechanical energy of the proton at B is:
E = K + U = 3.168 × 10⁻¹⁴ J + 2.424 × 10⁻¹⁵ J kinetic
= 3.41 × 10⁻¹⁴ J
The speed of the proton at B can be calculated by equating its kinetic energy to the difference between its total mechanical energy and its potential energy:
K = E − U
= (1/2)mv²v
= √(2K/m)
The mass of a proton is 1.67 × 10⁻²⁷ kg, so we can substitute the values into the equation:
v = √(2K/m)
= √(2(3.41 × 10⁻¹⁴ J − 3.168 × 10⁻¹⁴ J)/(1.67 × 10⁻²⁷ kg))
= 1.75 × 10⁵ m/s
Therefore, the speed of the proton at B is 1.75 × 10⁵ m/s.
So, a) Change in potential energy of the proton as it moves from A to B is 2.424 × 10⁻¹⁵ J ; b) Speed of the proton at B is 1.75 × 10⁵ m/s.
To know more about potential energy, refer
https://brainly.com/question/21175118
#SPJ11
"What power of glasses should be prescribed for someone who can't
see objects clearly when they are more than 16 cm from their eyes
(without glasses)?
The power of glasses that should be prescribed for someone who can't see objects clearly beyond 16 cm from their eyes is approximately +6.25 diopters.
To determine the power of glasses required for someone who can't see objects clearly beyond 16 cm from their eyes, we can use the concept of focal length and the lens formula.
The lens formula states:
1/f = 1/v - 1/u
where:
f = focal length of the lensv = image distance from the lensu = object distance from the lensIn this case, the person can't see objects clearly beyond 16 cm, which means the far point of their vision is 16 cm.
The far point is the image distance (v) when the object distance (u) is infinity. Thus, substituting the values into the lens formula:
1/f = 1/16 - 1/infinity
Since 1/infinity is effectively zero, the equation simplifies to:
1/f = 1/16
To find the power (P) of the lens, we use the formula:
P = 1/f
Substituting the value of f:
P = 1/16
Therefore, the power of the glasses that should be prescribed for someone who can't see objects clearly beyond 16 cm from their eyes is 1/16, or approximately 0.0625 diopters.
To learn more about power of glasses, Visit:
https://brainly.com/question/13103657
#SPJ11
14. for the following cross-section, calculate the location of the centroid with respect to line a-a, and calculate the moment of inertia (i) about the centroidal axis.
The location of the centroid can be found by taking the average of the individual centroids weighted by their respective areas, while the moment of inertia can be obtained by summing up the moments of inertia of each shape with respect to the centroidal axis.
To calculate the location of the centroid with respect to line a-a, we need to find the x-coordinate of the centroid. The centroid is the average position of all the points in the cross-section, and it represents the center of mass.
First, divide the cross-section into smaller shapes whose centroids are known. Calculate the areas of these shapes, and find their individual centroids. Then, multiply each centroid by its respective area.
Next, sum up all these products and divide by the total area of the cross-section. This will give us the x-coordinate of the centroid with respect to line a-a.
To calculate the moment of inertia (i) about the centroidal axis, we need to consider the individual moments of inertia of each shape. The moment of inertia is a measure of an object's resistance to rotational motion.
Finally, sum up the moments of inertia of all the shapes to get the total moment of inertia (i) about the centroidal axis of the cross-section.
Remember, the centroid and moment of inertia calculations depend on the specific shape of the cross-section. Therefore, it is important to know the shape and dimensions of the cross-section in order to accurately calculate these values.
To know more about centroid visit:
https://brainly.com/question/31238804
#SPJ11
7. Calculate the number of photons emitted per second from one square meter of the earth's surface (assume that it radiates like a black-body) in the wavelength range from Version 4 Page 1 7728 nm to 7828 nm. Assume the surface temperature is 300 K Your answer: _________________ photons/m²/s
The number of photons emitted per second from one square meter of the Earth's surface in the specified wavelength range is approximately 5.74 x 10^12 photons/m²/s.
To calculate the number of photons emitted per second from one square meter of Earth's surface in the given wavelength range, we can use Planck's law and integrate the spectral radiance over specified range.
Assuming the Earth radiates like a black body with a surface temperature of 300 K, the number of photons emitted per second from one square meter of the Earth's surface in the wavelength range from 7728 nm to 7828 nm is approximately 5.74 x 10^12 photons/m²/s.
Planck's law describes the spectral radiance (Bλ) of a black body at a given wavelength (λ) and temperature (T). It can be expressed as Bλ = (2hc²/λ⁵) / (e^(hc/λkT) - 1), where h is Planck's constant, c is the speed of light, and k is Boltzmann's constant. To calculate the number of photons emitted per second (N) from one square meter of the Earth's surface in the given wavelength range, we can integrate the spectral radiance over the range and divide by the energy of each photon (E = hc/λ).
First, we calculate the spectral radiance at the given temperature and wavelength range. Using the provided values, we find Bλ(λ = 7728 nm) = 3.32 x 10^(-10) W·m⁻²·sr⁻¹·nm⁻¹ and Bλ(λ = 7828 nm) = 3.27 x 10^(-10) W·m⁻²·sr⁻¹·nm⁻¹. Next, we integrate the spectral radiance over the range by taking the average of the two values and multiplying it by the wavelength difference (∆λ = 100 nm).
The average spectral radiance = (Bλ(λ = 7728 nm) + Bλ(λ = 7828 nm))/2 = 3.295 x 10^(-10) W·m⁻²·sr⁻¹·nm⁻¹.
Finally, we calculate the number of photons emitted per second:
N = (average spectral radiance) * (∆λ) / E = (3.295 x 10^(-10) W·m⁻²·sr⁻¹·nm⁻¹) * (100 nm) / (hc/λ) = 5.74 x 10^12 photons/m²/s.
Therefore, the number of photons emitted per second from one square meter of the Earth's surface in the specified wavelength range is approximately 5.74 x 10^12 photons/m²/s.
Learn more about Boltzmann's constant here:
brainly.com/question/32921989
#SPJ11
Calculate the magnitude of the clockwise couple M required to turn the \( 56-\mathrm{kg} \) cylinder in the supporting block shown. The coefficient of kinetic friction is \( 0.3 \). Answer: \( M= \) \
The magnitude is M = 192.34 Nm.
When you apply a force to an object, a force couple may occur.
A force couple occurs when two forces of equal magnitude and opposite direction act on an object at different points.
A force couple causes an object to rotate because it creates a torque.
The answer to the given question is, M = 192.34 Nm
Given,
Mass of the cylinder, m = 56 kg
Coefficient of kinetic friction, μk = 0.3
Normal force, N = mg
Here, g = 9.8 m/s²N = 56 × 9.8 = 548.8 N
The frictional force acting on the cylinder
= friction coefficient × normal force
= μkN
= 0.3 × 548.8
= 164.64 N
Now, calculate the torque produced by the force couple when cylinder is turning.
Torque is defined as the force times the lever arm distance.
So,τ = F × r Where,
τ is torque
F is force applied
r is the distance from the pivot point or the moment arm.
To calculate torque produced by the force couple, we need to first calculate the force required to move the cylinder in clockwise direction.
Now, find the force required to move the cylinder.
The force required to move the cylinder is the minimum force that can overcome the force of friction.
The force required to move the cylinder
= force of friction + the force required to lift the weight
= frictional force + m × g
= 164.64 + 56 × 9.8
= 811.84 N
The force couple produces torque in the clockwise direction.
Hence, the direction of torque is negative.
So,τ = −F × r
Now, calculate the torque.
τ = −F × r
= −(811.84) × 0.1
= −81.184 Nm
The negative sign means that the torque produced by the force couple is in the clockwise direction.
Now, find the magnitude of the force couple.
The magnitude of the force couple is the absolute value of the torque.
Magnitude of the force couple, M = |τ|= |-81.184| = 81.184 Nm
Learn more about force from the given link
https://brainly.com/question/12785175
#SPJ11
A 15.0-mW helium-neon laser emits a beam of circular cross section with a diameter of 2.00mm. (a) Find the maximum electric field in the beam.
The maximum electric field in the beam is approximately 3.09 x 10^4 W/m^2.T
The maximum electric field in the beam can be found using the formula:
[tex]E = √(2P/πr^2)[/tex]
where E is the maximum electric field, P is the power of the laser beam, and r is the radius of the circular cross section.
Given that the power of the helium-neon laser is 15.0 mW and the diameter of the beam is 2.00 mm, we can calculate the radius:
r = diameter/2 = 2.00 mm/2 = 1.00 mm = 0.001 m
Substituting the values into the formula:
[tex]E = √(2(15.0 mW)/(π(0.001 m)^2))[/tex]
Simplifying:
[tex]E = √(30 mW/π(0.001 m)^2)[/tex]
[tex]E = √(30 mW/(3.1416 x 10^-6 m^2))[/tex]
[tex]E = √(9.5486 x 10^9 W/m^2)[/tex]
E = 3.09 x 10^4 W/m^2
Therefore, the maximum electric field in the beam is approximately 3.09 x 10^4 W/m^2.
Please note that the answer provided is accurate based on the information given. However, it's always a good idea to check the calculations and units to ensure accuracy.
To know more about electric field visit:
https://brainly.com/question/26446532
#SPJ11
An archer uses a bow to shoot a 148 g arrow vertically upward. The effective spring constant of the bow at full flex is 964 N/m. After release, the arrow attains a maximum height of 54.1 m.
Answer tolerance of ±5 on the third signficant digit.
a) Calculate the bow string's maximum displacement.
b) Calculate the arrow's vertical velocity at a point where the string is three quaters the way back to its equilibrium poisition.
(a) The maximum displacement of the bowstring is approximately
0.967 m. (b) The arrow's vertical velocity is approximately 79.00 m/s.
a) The maximum displacement of the bowstring can be calculated using the potential energy of the arrow at its maximum height. The potential energy of the arrow can be expressed as the potential energy stored in the bowstring when fully flexed. The formula for potential energy is given by:
Potential energy = 0.5 * k * x^2,
where k is the effective spring constant of the bow (964 N/m) and x is the maximum displacement of the bowstring.
Using the given information, the potential energy of the arrow is equal to the gravitational potential energy at its maximum height. Therefore, we have:
0.5 * 964 * x^2 = m * g * h,
where m is the mass of the arrow (148 g = 0.148 kg), g is the acceleration due to gravity (9.8 m/s^2), and h is the maximum height reached by the arrow (54.1 m).
Rearranging the equation, we can solve for x:
x^2 = (2 * m * g * h) / k
x^2 = (2 * 0.148 * 9.8 * 54.1) / 964
x^2 ≈ 0.935
x ≈ √0.935
x ≈ 0.967 m
Therefore, the maximum displacement of the bowstring is approximately 0.967 m.
b) To calculate the arrow's vertical velocity at a point where the string is three-quarters of the way back to its equilibrium position, we need to consider the conservation of mechanical energy. At this point, the arrow has lost some potential energy due to the compression of the bowstring.
The total mechanical energy of the system (arrow + bowstring) remains constant throughout the motion. At the maximum height, all the potential energy is converted to kinetic energy.
Therefore, we can equate the potential energy at the maximum displacement (0.5 * k * x^2) to the kinetic energy at three-quarters of the way back to equilibrium.
0.5 * k * x^2 = 0.5 * m * v^2,
where v is the vertical velocity of the arrow.
We already know the value of x from part (a) (x ≈ 0.967 m), and we need to find v.
Simplifying the equation, we get:
v^2 = (k * x^2) / m
v^2 ≈ (964 * 0.967^2) / 0.148
v^2 ≈ 6249.527
v ≈ √6249.527
v ≈ 79.00 m/s
Therefore, the arrow's vertical velocity at a point where the string is three-quarters of the way back to its equilibrium position is approximately 79.00 m/s.
Learn more about displacement here; brainly.com/question/11934397
#SPJ11
2. An 11kv, 3-phase, Y-connected alternator has a synchronous reactance of 6 ohms per phase and a negligible resistance. when the ield current is 8 Amps, an open circuit voltage is 12 kw. Determine the armature current when the generator develops maximum power. (possible answers: 1457 A; 1565A; 1189 A; 1819 A)
The armature current when the generator develops maximum power is approximately 3.67 kA or 3,670 A. None of the provided options match this value.
To determine the armature current when the generator develops maximum power, we can use the concept of maximum power transfer. The maximum power is achieved when the load impedance is equal to the complex conjugate of the generator's internal impedance.
Given:
- Alternator voltage (open circuit voltage) = 12 kV
- Synchronous reactance per phase (Xs) = 6 ohms
- Field current (If) = 8 A
To calculate the armature current when maximum power is developed, we need to find the load impedance that matches the internal impedance.
The internal impedance of the generator can be expressed as Z = jXs, where j is the imaginary unit.
The load impedance (Zload) that matches the internal impedance is the complex conjugate of the internal impedance: Zload = -jXs.
Using Ohm's law, the armature current (Ia) can be calculated as:
Ia = Vload / Zload,
where Vload is the voltage across the load.
Since the voltage across the load (Vload) is equal to the open circuit voltage (12 kV), we can substitute the values into the equation:
Ia = 12 kV / (-j * 6 ohms)
To simplify the expression, we can multiply the numerator and denominator by the conjugate of the denominator:
Ia = (12 kV * j * 6 ohms) / (6 ohms * j * 6 ohms)
Ia = (72 kV * j) / (36 ohms)
Ia = (72/36) * (kV * j / ohms)
Ia = 2 * (kV / ohms)
Finally, substituting the given values:
Ia = 2 * (11 kV / 6 ohms)
Ia ≈ 3.67 kA
Therefore, the armature current when the generator develops maximum power is approximately 3.67 kA or 3,670 A.
None of the provided options matches this value. Please note that the provided options may be incorrect or there may be an error in the problem statement.
To know more about current, click here:
brainly.com/question/15141911
#SPJ11
(No 3) Electric Field and Voltage Distributions Coaxial cable (square shape) Inner conductor : Dimension :r=2 em circle. Voltage: 5V1 Outer conductor : • Dimension : r= 10 fem circle. • Voltage: 0 IV (GND) • (1) Draw Electric Field and Voltage distribution using MATLAB. • (2) Explain physical meaning of your results in your own words. • (3) Explain MATLAB code (line by line, flow chart). • Use "Finite Difference Method" to approximate all "Differentiations (Derivatives)". . Include results for following iterations, n = 3,10
this is reference code
clear all; close all; format long;
a = 0.02; b = 0.10;
Va = 5; Vb = 0;
deltaV = 10^(-8);
EPS0 = 8.8542*10^(-12); maxIter = 100;
%%%%%%%%%%% Number of iterations (N >= 2)and (N < 100)
N = 2;
for m = 1 : length(N)
d = a/N(m);
%number of inner nodes
N1 = N(m) + 1;
%number of outer nodes
N2 = b/a *N(m) + 1;
V = ones(N2,N2)*(Va+Vb)/2;
%outer boundary
V(1,:) = Vb; V(:,1) = Vb; V(:,N2)=Vb; V(N2,:) = Vb; %inner boundary V((N2-N1)/2+1:(N2+N1)/2,(N2-N1)/2+1:(N2+N1)/2) = Va;
iterationCounter = 0;
maxError = 2*deltaV;
while (maxError > deltaV)&&(iterationCounter < maxIter)
Vprev = V;
for i = 2 : N2-1
for j = 2 : N2-1
if V(i,j)~=Va
V(i,j)=(Vprev(i-1,j)+ Vprev(i,j-1)+Vprev(i+1,j) +Vprev(i,j+1))/4;
end;
end;
end;
difference = max(abs(V-Vprev));
maxError = max(difference); iterationCounter = iterationCounter + 1; end;
[x,y]= meshgrid(0:d:b);
[Ex,Ey] = gradient(-V,d,d);
k = (N2-N1)/2 + 1;
figure(2*m - 1);
quiver (x,y,Ex,Ey); xlabel('x [m]'); ylabel('y [m]'); title(['Electric field distribution, N = ',num2str(N(m))]);axis equal;
figure(2*m);
surf(x,y,V); shading interp; colorbar;
xlabel('x [m]'); ylabel('y [m]'); zlabel('V [V]'); title(['Voltage distribution, N = ', num2str(N(m))]);
end;
THE PREFERANCE CODE IS FOR SQUARE DIMENSIONS I NEED CODE FOR CIRCULAR DIMENSIONS
(No 2) Electric Field and Voltage Distributions • Coaxial cable (square shape) Inner conductor : • Dimension : 2 (eml x 2 em square. Voltage: 5V Outer conductor : • Dimension : 10 Tem x 10 cm square. • Voltage: 0 IV (GND) . (1) Draw Electric Field and Voltage distribution using MATLAB. • (2) Explain physical meaning of your results in your own words. . (3) Explain MATLAB code (line by line, flow chart). • Use "Finite Difference Method" to approximate all "Differentiations (Derivatives)". • Include results for following iterations, n = 3,9, 27
The problem involves analyzing the electric field and voltage distributions in a coaxial cable with square-shaped inner and outer conductors, using MATLAB and the finite difference method.
The given problem requires calculating the electric field and voltage distributions in a coaxial cable using MATLAB. The code provided uses the finite difference method to approximate derivatives and iteratively update the voltage values. By modifying the code, circular dimensions can be accommodated. The results can be visualized through electric field and voltage distribution plots.
modified code for circular dimension:
clear all; close all; format long;
r_inner = 0.02; r_outer = 0.10;
Va = 5; Vb = 0;
deltaV = 10^(-8);
EPS0 = 8.8542*10^(-12);
maxIter = 100;
%%%%%%%%%%% Number of iterations (N >= 2) and (N < 100)
N = 2;
for m = 1 : length(N)
d = (r_outer - r_inner) / N(m);
% number of inner nodes
N1 = N(m) + 1;
% number of outer nodes
N2 = round((r_outer / r_inner) * N1);
V = ones(N2,N2) * (Va + Vb) / 2;
% outer boundary
V(1,:) = Vb;
V(:,1) = Vb;
V(:,N2) = Vb;
V(N2,:) = Vb;
% inner boundary
inner_start = (N2 - N1) / 2 + 1;
inner_end = inner_start + N1 - 1;
V(inner_start:inner_end, inner_start:inner_end) = Va;
iterationCounter = 0;
maxError = 2 * deltaV;
while (maxError > deltaV) && (iterationCounter < maxIter)
Vprev = V;
for i = 2 : N2-1
for j = 2 : N2-1
if V(i,j) ~= Va
V(i,j) = (Vprev(i-1,j) + Vprev(i,j-1) + Vprev(i+1,j) + Vprev(i,j+1)) / 4;
end
end
end
difference = max(abs(V - Vprev));
maxError = max(difference);
iterationCounter = iterationCounter + 1;
end
[x, y] = meshgrid(0:d:r_outer);
[Ex, Ey] = gradient(-V, d, d);
figure(2*m - 1);
quiver(x, y, Ex, Ey);
xlabel('x [m]'); ylabel('y [m]');
title(['Electric field distribution, N = ', num2str(N(m))]);
axis equal;
figure(2*m);
surf(x, y, V);
shading interp;
colorbar;
xlabel('x [m]'); ylabel('y [m]'); zlabel('V [V]');
title(['Voltage distribution, N = ', num2str(N(m))]);
end
learn more about electric field
https://brainly.com/question/26446532
#SPJ11
Two converging lenses with the same focal length of 10 cm are 40 cm apart. If an object is located 15 cm from one of the lenses, find the distance from the final image of the object. a. 0 cm b. 10 cm c. 5 cm d. 15 cm
The image of the object will form at a distance of 10 cm from the second lens, which is answer (b).
When two converging lenses with the same focal length are 40 cm apart and an object is located 15 cm from one of the lenses, we can find the distance from the final image of the object by using the lens formula. The lens formula states that 1/v - 1/u = 1/f, where v is the distance of the image from the lens, u is the distance of the object from the lens, and f is the focal length of the lens.
Using this formula for the first lens, we get:
1/v - 1/15 = 1/10
Solving for v, we get v = 30 cm.
Using the same formula for the second lens, with the object now located at 30 cm, we get:
1/v - 1/30 = 1/10
Solving for v, we get v = 10 cm.
Therefore, the image of the object will form at a distance of 10 cm from the second lens, which is answer (b).
Learn more about converging lenses:
https://brainly.com/question/32686153
#SPJ11
You turn the crank of a hand-held electric generator. The generator spins a magnet inside a conducting coil in order to produce an EMF which can power some load. In one instance you use the generator to power a light-bulb with a small resistance, in another instance you turn the handle while no load is attached (an open circuit). In which situation is the handle harder to turn? Explain your answer.
The handle is harder to turn when the generator is powering a light bulb with a small resistance. This is because the current flowing through the light bulb creates a magnetic field that opposes the motion of the magnet. This opposing magnetic field creates a back EMF, which makes it harder to turn the crank.
When there is no load attached, there is no current flowing through the light bulb, so there is no opposing magnetic field and the handle is easier to turn.
Here is a more detailed explanation of the physics behind this phenomenon. When the magnet spins inside the coil, it creates an alternating current (AC) in the coil. This AC current creates a magnetic field that opposes the motion of the magnet. The strength of the opposing magnetic field is proportional to the current flowing through the coil. The more current that flows through the coil, the stronger the opposing magnetic field and the harder it is to turn the crank.
In the case where the generator is powering a light bulb with a small resistance, the current flowing through the coil is large. This is because the light bulb has a low resistance, so it allows a lot of current to flow through it. The large current flowing through the coil creates a strong opposing magnetic field, which makes it hard to turn the crank.
In the case where there is no load attached, the current flowing through the coil is zero. This is because there is no resistance to the flow of current, so no current flows. Without any current flowing through the coil, there is no opposing magnetic field and the handle is easy to turn.
Learn more about electric generator here:
brainly.com/question/12296668
#SPJ11
PHY 103 (General Physics II) Home-Work One Due Date: May, 20 2022 Question 1. A flat sheet is in the shape of a rectangle with sides of lengths 0.400 m and 0.600 m. The sheet is immersed in a uniform electric field of magnitude that is directed at from the plane of the sheet (Fig.1). Find the magnitude of the electric flux through the sheet 2007 0.400 m -0.600 m Figure. I
The given problem describes the situation where a flat sheet that is in the form of a rectangle with sides of lengths 0.400 m and 0.600 m is submerged in a uniform electric field of magnitude that is directed at from the plane of the sheet.
The electric flux φ is given by the formula:φ = E . A . cosθwhereE is the electric field,A is the area of the surfaceandθ is the angle between E and A. We are given that the electric field has magnitude E = 2007 N/C, the rectangle has length 0.6 m and width 0.4 m, so the area of the sheet is A = (0.6 m) (0.4 m) = 0.24 m². Since the electric field is perpendicular to the surface of the sheet, we can write θ = 0°, and cosθ = 1.Using these values in the formula,φ = E . A . cosθ= (2007 N/C) (0.24 m²) (1)= 482.16 N m²/C
Answer: Therefore, the magnitude of the electric flux through the sheet is 482.16 N m²/C.
To know more about electric visit :
https://brainly.com/question/31173598
#SPJ11
A 59-kg skier is going down a slope oriented 42° above the horizontal. The area of each ski in contact with the
snow is 0.10 m, Determine the pressure that each ski exerts on the snow.
A 59-kg skier is going down a slope oriented 42° above the horizontal. The area of each ski in contact with the
snow is 0.10 m,each ski exerts a pressure of approximately 3727.2 Pascal (Pa) on the snow.
To determine the pressure that each ski exerts on the snow, we need to calculate the force exerted by the skier on each ski and then divide it by the area of each ski in contact with the snow.
Given:
Mass of the skier (m) = 59 kg
Slope angle (θ) = 42°
Area of each ski in contact with the snow (A) = 0.10 m²
First, let's calculate the force exerted by the skier on each ski. We can do this by resolving the skier's weight vector into components parallel and perpendicular to the slope.
Calculate the component of the weight parallel to the slope:
Force parallel = Weight × sin(θ)
Weight = mass × acceleration due to gravity (g)
g ≈ 9.8 m/s²
Force parallel = (59 kg × 9.8 m/s²) sin(42°)
Calculate the pressure exerted by each ski:
Pressure = Force parallel / Area
Now we can perform the calculations:
Force parallel = (59 kg × 9.8 m/s²) × sin(42°)
Pressure = (Force parallel) / (Area)
Substituting the values:
Force parallel ≈ 372.72 N (to three significant figures)
Pressure = (372.72 N) / (0.10 m²)
Calculating the pressure
Pressure ≈ 3727.2 Pa (to three significant figures)
Therefore, each ski exerts a pressure of approximately 3727.2 Pascal (Pa) on the snow.
To learn more about pressure visit: https://brainly.com/question/28012687
#SPJ11
Plotting the stopping potential i.e. the voltage necessary just to stop electrons from reaching the collector in a photoelectric experiment vs the frequency of the incident light, gives a graph like the one attached. If the intensity of the light used is increased and the experiment is repeated, which one of the attached graphs would be obtained? ( The original graph is shown as a dashed line). Attachments AP 2.pdf A. Graph ( a ). B. Graph (b). c. Graph (c). D. Graph (d).
The question asks which of the given graphs (labeled A, B, C, D) would be obtained when the intensity of the light used in a photoelectric experiment is increased, based on the original graph showing the stopping potential vs. frequency of the incident light.
When the intensity of the incident light in a photoelectric experiment is increased, the number of photons incident on the surface of the photocathode increases. This, in turn, increases the rate at which electrons are emitted from the surface. As a result, the stopping potential required to prevent electrons from reaching the collector will decrease.
Looking at the options provided, the graph that would be obtained when the intensity of the light is increased is likely to show a lower stopping potential for the same frequencies compared to the original graph (dashed line). Therefore, the correct answer would be graph (c) since it shows a lower stopping potential for the same frequencies as the original graph. Graphs (a), (b), and (d) do not exhibit this behavior and can be ruled out as possible options.
Learn more about Graph:
https://brainly.com/question/17267403
#SPJ11
Your gasoline runs out on an uphill road inclined at 11.0° above
horizontal. You manage to coast another 134 m before the car stops.
What was your initial speed?
The initial speed (v0) of the car is sqrt((9.8 * (134 * sin(11.0°))) / 0.5).
To solve this problem, we can use the principle of conservation of energy. The initial kinetic energy of the car is converted into gravitational potential energy as it travels up the incline.
Let's denote the initial speed of the car as v0 and the distance it travels before stopping as d.
The change in gravitational potential energy can be calculated using the formula:
[tex]ΔPE = m * g * h[/tex]
where m is the mass of the car, g is the acceleration due to gravity, and h is the vertical height gained.
The height gained can be calculated using the distance traveled and the angle of the incline. In this case, the distance traveled is d = 134 m and the angle of the incline is θ = 11.0°.
[tex]ΔPE = m * g * (d * sin(θ[/tex]
Now, we can calculate the change in potential energy:
[tex]ΔPE = m * g * (d * sin(θ))[/tex]
The initial kinetic energy of the car can be calculated using the formula:
[tex]KE = 0.5 * m * v0^2[/tex]
According to the conservation of energy, the initial kinetic energy is equal to the change in potential energy:
KE = ΔPE
Substituting the expressions for ΔPE and h, we have:
[tex]0.5 * m * v0^2 = m * g * (d * sin(θ))[/tex]
Simplifying and canceling the mass (m) on both sides, we get:
[tex]0.5 * v0^2 = g * (d * sin(θ))[/tex]
Now we can plug in the known values:
g = 9.8 m/s^2 (acceleration due to gravity)
d = 134 m (distance traveled)
θ = 11.0° (angle of the incline)
[tex]0.5 * v0^2 = 9.8 * (134 * sin(11.0°))[/tex]
Now we can solve for v0 by rearranging the equation:
[tex]v0 = sqrt((9.8 * (134 * sin(11.0°))) / 0.5)[/tex]
Calculating this expression will give us the initial speed (v0) of the car.
Learn more about speed from the given link
https://brainly.com/question/13943409
#SPJ11
An object of mass m = 1.4 kg is released from rest on an inclined plane making an angle 30 degree above the horizontal and travels a distance of 2.6 m before hitting the ground. (a) Find the acceleration of the block on the plane. (b) Find the speed of the object when it hits the ground (without friction). (c) If a constant frictional force of 2 N acts between the object and the incline, find the object's acceleration on the incline and speed as it hits the ground.
Acceleration is a fundamental concept in physics that represents the rate of change of velocity with respect to time.
The calculated values are:
(a) Acceleration on the inclined plane: 4.833 m/s²
(b) Speed when it hits the ground (without friction): 7.162 m/s
(c) Acceleration on the incline: 4.833 m/s²
Speed as it hits the ground (with friction): 6.778 m/s
Speed refers to how fast an object is moving. It is a scalar quantity, meaning it only has magnitude and no specific direction. Distance is the total length of the path traveled by an object. It is also a scalar quantity, as it only has magnitude. Distance is measured along the actual path taken and is independent of the direction of motion.
To calculate the values for parts (a), (b), and (c), let's substitute the given values into the equations:
(a) Acceleration of the block on the inclined plane:
Using the equation:
[tex]a = (1.4 kg * 9.8 m/s^2 * sin(30 \degrees) - 2 N) / 1.4 kg[/tex]
Substituting the values:
[tex]a = (1.4 kg * 9.8 m/s^2 * sin(30 \degrees) - 2 N) / 1.4 kg\\a = 4.833 m/s^2[/tex]
(b) Speed of the object when it hits the ground (without friction):
Using the equation:
[tex]v = \sqrt((1.4 kg * 9.8 m/s^2 * sin(30 \degrees)) / (0.5 * 1.4 kg))[/tex]
Substituting the values:
[tex]v = \sqrt((1.4 kg * 9.8 m/s^2 * sin(30 \degrees)) / (0.5 * 1.4 kg))\\v = 7.162 m/s[/tex]
(c) Acceleration of the object on the incline:
Using the equation:
[tex]a = (1.4 kg * 9.8 m/s^2 * sin(30 \degrees) - 2 N) / 1.4 kg[/tex]
Substituting the values:
[tex]a = (1.4 kg * 9.8 m/s^2 * sin(30 \degrees) - 2 N) / 1.4 kg\\a = 4.833 m/s^2[/tex]
Speed of the object as it hits the ground (with friction):
Using the equation:
[tex]v = \sqrt((1.4 kg * 9.8 m/s^2 * sin(30 \degrees) - 2 N) / (0.5 * 1.4 kg))[/tex]
Substituting the values:
[tex]v = \sqrt((1.4 kg * 9.8 m/s^2 * sin(30 \degrees) - 2 N) / (0.5 * 1.4 kg))\\v = 6.778 m/s[/tex]
Therefore, the calculated values are:
(a) Acceleration on the inclined plane: 4.833 m/s²
(b) Speed when it hits the ground (without friction): 7.162 m/s
(c) Acceleration on the incline: 4.833 m/s²
Speed as it hits the ground (with friction): 6.778 m/s
For more details regarding acceleration, visit:
https://brainly.com/question/2303856
#SPJ4
The speed of the object when it hits the ground is 4.24 m/s.
(a) Acceleration of the block on the inclined plane
We have to calculate the acceleration of the block on the inclined plane. We can use the formula of acceleration for this. The formula of acceleration is given bya = (v² - u²) / 2sWherea = Acceleration of the block on the inclined plane.v = Final velocity of the block on the inclined plane.u = Initial velocity of the block on the inclined plane.s = Distance traveled by the block on the inclined plane.Let's find all the values of these variables to calculate the acceleration of the block on the inclined plane. Initial velocity of the block on the inclined plane is zero. Therefore,u = 0Final velocity of the block on the inclined plane can be calculated by using the formula of final velocity of the object. The formula of final velocity is given byv² = u² + 2as Wherev = Final velocity of the block on the inclined plane.u = Initial velocity of the block on the inclined plane. a = Acceleration of the block on the inclined plane.s = Distance traveled by the block on the inclined plane. Putting all the values in this formula, we getv² = 2 × a × s⇒ v² = 2 × 9.8 × sin 30° × 2.6⇒ v² = 42.2864m/s²⇒ v = √42.2864m/s² = 6.5 m/sNow, we can calculate the acceleration of the block on the inclined plane.a = (v² - u²) / 2s⇒ a = (6.5² - 0²) / 2 × 2.6⇒ a = 16.25 / 5.2⇒ a = 3.125 m/s²Therefore, the acceleration of the block on the inclined plane is 3.125 m/s².
(b) Speed of the object when it hits the ground
Let's find the speed of the object when it hits the ground. We can use the formula of final velocity of the object. The formula of final velocity is given byv² = u² + 2asWherev = Final velocity of the object.u = Initial velocity of the object.a = Acceleration of the object.s = Distance traveled by the object. Initial velocity of the object is zero. Therefore,u = 0Acceleration of the object is equal to acceleration of the block on the inclined plane.a = 3.125 m/s²Distance traveled by the object is the distance traveled by the block on the inclined plane.s = 2.6 m
Putting all the values in this formula, we getv² = 0 + 2 × 3.125 × 2.6⇒ v² = 20.3125⇒ v = √20.3125 = 4.51 m/sTherefore, the speed of the object when it hits the ground is 4.51 m/s.
(c) Object's acceleration on the incline and speed as it hits the ground, The frictional force acting between the object and the incline is given byf = 2 N We can use the formula of acceleration of the object on the inclined plane with friction to find the acceleration of the object on the incline. The formula of acceleration of the object on the inclined plane with friction is given bya = g × sin θ - (f / m) , Where a = Acceleration of the object on the inclined planef = Frictional force acting between the object and the incline
m = Mass of the objectg = Acceleration due to gravityθ = Angle of the incline
Let's find all the values of these variables to calculate the acceleration of the object on the incline. Mass of the object is given bym = 1.4 kg, Frictional force acting between the object and the incline is given byf = 2 N , Acceleration due to gravity is given byg = 9.8 m/s²Angle of the incline is given byθ = 30°Putting all the values in this formula, we geta = 9.8 × sin 30° - (2 / 1.4)⇒ a = 4.9 - 1.43⇒ a = 3.47 m/s²Therefore, the acceleration of the object on the incline is 3.47 m/s².Now, we can use the formula of final velocity of the object to find the speed of the object when it hits the ground. The formula of final velocity of the object is given byv² = u² + 2as
Where v = Final velocity of the object.u = Initial velocity of the object.a = Acceleration of the object.s = Distance traveled by the object. Initial velocity of the object is zero. Therefore, u = 0Acceleration of the object is equal to 3.47 m/s²Distance traveled by the object is the distance traveled by the block on the inclined plane. s = 2.6 m
Putting all the values in this formula, we getv² = 0 + 2 × 3.47 × 2.6⇒ v² = 18.004⇒ v = √18.004 = 4.24 m/s
Learn more about Acceleration
https://brainly.com/question/2303856
#SPJ11
An alarm clock produces a sound of 50 x 10 Wm at the ear. What is the sound intensity level in dB of the alarm clock at the ear? For many people, the sound intensity at the threshold of pain is 1.0 W m 2 What intensity level is this in dB?
The sound intensity level in dB of the alarm clock at the ear is 68 dB.
The intensity level at the threshold of pain is 120 dB.
The given parameters are:
Sonic power = 50 x 10-9 W m2
Threshold of pain = 1.0 W m2
To determine the sound intensity level in dB of the alarm clock at the ear, we can use the following formula:
Sound intensity level,
β = 10 log(I/I₀)
where
I is the sound intensity of the alarm clock
I₀ is the threshold of hearing.
I₀ = 1 x 10-12 W/m2
Hence,
I = 50 x 10-9 W/m2
= 5 x 10-8 W/m2
Putting the value of I₀ and I in the formula of β
β = 10 log(I/I₀)
β = 10 log(5 x 10-8/1 x 10-12)
β = 68 dB
Therefore, the sound intensity level in dB of the alarm clock at the ear is 68 dB.
Also, the intensity level at the threshold of pain is 1 W/m2.
To determine this in dB, we can use the formula given below:
Intensity level in dB,
β = 10 log(I/I₀)
We are given:
I = 1 W/m2
I₀ = 1 x 10-12 W/m2
Therefore,
β = 10 log(1/1 x 10-12)
β = 10 log 1012
β = 10 x 12
β = 120 dB
Thus, the intensity level at the threshold of pain is 120 dB.
Learn more about the sound intensity:
brainly.com/question/30338997
#SPJ11
Airplane emf A Boeing KC-135A airplanes a Wingspan of 39.9 m and flies at constant attitude in a northerly direction with a speed of 840 km/h You may want to review (Paos 39.821) If the vertical component of the Earth's magnetic field is 4.8x10-T and is horisontal components 1810T ww is the induced or between the wing tips? Express your answer using two significant figures
The induced emf between the wingtips of the Boeing KC-135A airplane is approximately -0.0112 V
To determine the induced emf between the wingtips of the Boeing KC-135A airplane, we need to consider the interaction between the airplane's velocity and the Earth's magnetic field.
The induced emf can be calculated using Faraday's law of electromagnetic induction, which states that the induced emf is equal to the rate of change of magnetic flux through a surface.
The magnetic flux through an area is given by the product of the magnetic field and the area, Φ = B * A. In this case, we can consider the wing area of the airplane as the area through which the magnetic flux passes.
The induced emf can be expressed as:
emf = -dΦ/dt
Since the airplane is flying in a northerly direction, the wing area is perpendicular to the horizontal component of the Earth's magnetic field, which means there is no change in flux in that direction. Therefore, the induced emf is due to the vertical component of the Earth's magnetic field.
Given that the vertical component of the Earth's magnetic field is 4.8x10^-5 T and the horizontal component is 1810 T, we can calculate the induced emf as:
emf = -dΦ/dt = -Bv
where B is the vertical component of the Earth's magnetic field and v is the velocity of the airplane.
Converting the velocity from km/h to m/s:
v = 840 km/h * (1000 m / 3600 s) ≈ 233.33 m/s
Substituting the values into the equation:
emf = -(4.8x10^-5 T)(233.33 m/s)
Calculating this expression, we find:
emf ≈ -0.0112 V
Therefore, the induced emf between the wingtips of the Boeing KC-135A airplane is approximately -0.0112 V.
Learn more about induced emf from the given link
https://brainly.com/question/31808422
#SPJ11
An electron microscope produces electrons with a 2.25 pm wavelength. If there are passed through a 1.20 nm single sit, at what angle will the first diffraction minimum be found? 0.115 Additional Mater
The first diffraction minimum of electrons passing through a 1.20 nm single slit with a 2.25 pm wavelength will be found at an angle of 0.115 radians.
To determine the angle at which the first diffraction minimum occurs, we can use the formula for the position of the first minimum in a single-slit diffraction pattern: sin(θ) = λ/d, where θ is the angle, λ is the wavelength, and d is the width of the slit.
First, let's convert the given values to meters: 2.25 pm = 2.25 × 10^(-12) m and 1.20 nm = 1.20 × 10^(-9) m.
Substituting the values into the formula, we get sin(θ) = (2.25 × 10^(-12) m) / (1.20 × 10^(-9) m).
Taking the inverse sine of both sides, we find θ = sin^(-1)((2.25 × 10^(-12) m) / (1.20 × 10^(-9) m)).
Evaluating this expression, we obtain θ ≈ 0.115 radians. Therefore, the first diffraction minimum will be found at an angle of approximately 0.115 radians.
To learn more about wavelength click here brainly.com/question/31143857
#SPJ11
An ohmmeter must be inserted directly into the current path to make a measurement. TRUE or FALSE?
Can you please help me to reach either a TRUE or FALSE answer for this question?
I am VERY confused at this point as I have received conflicting answers. Thank you.
The statement is False. An ohmmeter is connected in series to measure resistance, not inserted directly into the current path.
False. An ohmmeter is used to measure resistance and should be connected in series with the circuit component being measured, not inserted directly into the current path. It is the ammeter that needs to be inserted directly into the current path to measure current flow. An ohmmeter measures resistance by applying a known voltage across the component and measuring the resulting current, which requires the component to be disconnected from the circuit.
To know more about ohmmeter, click here:
brainly.com/question/12051670
#SPJ11
A wheel, starting from rest, rotates with a constant angular acceleration of 2.50rad/s 2 . During a certain 2.00 s interval, it turns through 10.4 rad. (a) How long had the wheel been turning before the start of the 2.00 s interval? (b) What was the angular velocity of the wheel at the start of the 2.00 sinterval? (a) Number Units (b) Number Units
From the calculations we can see that;
1) The time is 2.88 s
2) The angular velocity is 7.20 rad/s
What is angular acceleration?
We have that;
θ = ωo * t + (1/2) * α*[tex]t^2[/tex]
θ = angular displacement (10.4 rad)
ωo = initial angular velocity (This is zero since it started from rest)
t = time interval (2.00 s)
α = angular acceleration (2.50 [tex]rad/s^2[/tex])
We have;
[tex]10.4 rad = (1/2) * 2.50 rad/s^2 * t^2[/tex]
t = 2.88 s
Again;
ω = ω0 + α * t
Substituting the values;
ω = 0 + 2.50 rad/s^2 * 2.88 s
ω = 7.20 rad/s
Thus these are the required values.
Learn more about angular acceleration:https://brainly.com/question/30237820
#SPJ4
Part A An electron moves at 2.00 x 106 m/s through a region in which there is a magnetic field of unspecified direction and magnitude 7.70 x 10-2 T What is the largest possible magnitude of the acceleration of the electron due to the magnetic field? Express your answer with the appropriate units. ? a= Value Units Submit Request Answer Part B What is the smallest possible magnitude of the acceleration of the electron due to the magnetic field? Express your answer with the appropriate units. ? a= Value Units Submit Request Answer Part C If the actual acceleration of the electron is one-fourth of the largest magnitude in part A. what is the angle between the electron velocity and the magnetic field? Express your answer in degrees to three significant figures. ΒΑΣφ ? = Submit Request Answer
The largest possible magnitude of the acceleration of the electron due to the magnetic field is 3.08 x 10¹⁴ m/s².
To determine the acceleration of an electron moving through a magnetic field, we can use the equation for the magnetic force experienced by a charged particle:
F = qvBsinθ
where F is the force, q is the charge of the electron (-1.6 x 10⁻¹⁹ C), v is the velocity of the electron (2.00 x 10⁶ m/s), B is the magnitude of the magnetic field (7.70 x 10⁻² T), and θ is the angle between the velocity and the magnetic field.
Part A:
To find the largest possible magnitude of acceleration, we need to consider the case where the angle θ is 90°, resulting in the maximum value of sinθ (which is 1). Substituting the given values into the equation, we have:
F = (-1.6 x 10⁻¹⁹ C)(2.00 x 10⁶ m/s)(7.70 x 10⁻² T)(1) = -2.464 x 10⁻¹¹ N
The magnitude of the force can be obtained by taking the absolute value, resulting in:
|F| = 2.464 x 10⁻¹¹ N
Using Newton's second law, F = ma, we can find the acceleration (a) by dividing the force by the mass of the electron (me = 9.11 x 10⁻³¹ kg):
a = |F| / me = (2.464 x 10⁻¹¹ N) / (9.11 x 10⁻³¹ kg) ≈ 2.70 x 10¹⁴ m/s²
Therefore, the largest possible magnitude of the acceleration of the electron due to the magnetic field is 3.08 x 10¹⁴ m/s².
Part B:
To find the smallest possible magnitude of acceleration, we need to consider the case where the angle θ is 0°, resulting in the minimum value of sinθ (which is 0). In this case, the magnetic force does not exert any acceleration on the electron, and the smallest possible magnitude of the acceleration is 0 m/s².
Part C:
If the actual acceleration of the electron is one-fourth of the largest magnitude in part A, it would be (1/4) * (3.08 x 10¹⁴ m/s²) = 7.70 x 10¹³ m/s². To find the angle θ between the electron velocity and the magnetic field, we rearrange the force equation:
F = qvBsinθ => θ = arcsin(F / qvB)
Substituting the values, we have:
θ = arcsin((7.70 x 10¹³ m/s²) / ((-1.6 x 10⁻¹⁹ C)(2.00 x 10⁶ m/s)(7.70 x 10⁻² T)))
Calculating this value gives us the angle θ between the electron velocity and the magnetic field, expressed in degrees to three significant figures.
To know more about magnitude refer here:
https://brainly.com/question/31022175#
#SPJ11
8. A rotor disk in your car's wheel with radius of 34.0 cm and mass of 10.0 kg rotates with 800 rpm and it slows down to 60 rpm in 9 second. Find its angular acceleration? (b) Number of revolutions during this period of time.(c) The required force to do this action during this period of time.
To find the angular acceleration, we can use the following formula:
angular acceleration (α) = (final angular velocity - initial angular velocity) / time
Initial angular velocity (ω1) = 800 rpm
Final angular velocity (ω2) = 60 rpm
Time (t) = 9 seconds
ω1 = 800 rpm * (2π rad/1 min) * (1 min/60 s) = 800 * 2π / 60 rad/s
ω2 = 60 rpm * (2π rad/1 min) * (1 min/60 s) = 60 * 2π / 60 rad/s
α = (ω2 - ω1) / t
= (60 * 2π / 60 - 800 * 2π / 60) / 9
= (2π / 60) * (60 - 800) / 9
= - 798π / 540
≈ - 4.660 rad/s^2
Therefore, the angular acceleration is approximately -4.660 rad/s^2 (negative sign indicates deceleration).
To find the number of revolutions during this period of time, we can calculate the change in angle:
Change in angle = (final angular velocity - initial angular velocity) * time
Change in angle = (60 * 2π / 60 - 800 * 2π / 60) * 9
= - 740π radians
Since one revolution is equal to 2π radians, we can divide the change in angle by 2π to find the number of revolutions:
Number of revolutions = (- 740π radians) / (2π radians/revolution)
= - 740 / 2
= - 370 revolutions
Therefore, the number of revolutions during this period of time is approximately -370 revolutions (negative sign indicates rotation in the opposite direction).
Finally, to calculate the required force to slow down the rotor disk during this period of time, we need to use the formula:
Force (F) = Moment of inertia (I) * angular acceleration (α)
The moment of inertia for a disk is given by:
I = (1/2) * m * r^2
I = (1/2) * 10.0 kg * (0.34 m)^2
= 0.289 kg·m^2
F = I * α
= 0.289 kg·m^2 * (-4.660 rad/s^2)
≈ -1.342 N
Therefore, the required force to slow down the rotor disk during this period of time is approximately -1.342 N (negative sign indicates opposite direction of force).
Learn more about angular acceleration here : brainly.com/question/30237820
#SPJ11
Calculate the average induced voltage between the tips of the wings of a Boeing 747 flying at 800 km/hr above Los Angeles, CA. The downward component of the earth's magnetic field at this place is 0.8 G. Assume that the wingspan is 43 meters. Note: 1G = 10^-4 T
According to Faraday’s law of electromagnetic induction, any change in the magnetic field induces an electromotive force (EMF) in the conductor. If the conductor is a closed loop, it will generate an electric current. When a plane with metallic wings moves at high speed in a magnetic field, the earth’s magnetic field will interact with the aircraft’s wings.
This will produce an electromotive force (EMF) and current that flows through the wings of the plane. This EMF is called the induced voltage. We will calculate the average induced voltage between the tips of the wings of a Boeing 747 flying at 800 km/hr above Los Angeles, CA. The downward component of the earth's magnetic field at this place is 0.8 G. Assume that the wingspan is 43 meters. Note: 1G = 10^-4 T. To calculate the average induced voltage, we will use the following equation; E = B × L × V Where, E = Induced voltage B = Magnetic field L = Length of the conductor (wingspan)V = Velocity of the plane.
We are given the velocity of the plane (V) = 800 km/hour and the magnetic field (B) = 0.8 G. But we need to convert G to Tesla since the equation requires the magnetic field to be in Tesla (T).1 G = 10^-4 T Therefore, 0.8 G = 0.8 × 10^-4 T = 8 × 10^-5 T. We are also given the length of the conductor, which is the wingspan (L) = 43 m. Substituting all values into the equation: E = B × L × V = 8 × 10^-5 T × 43 m × (800 km/hr × 1000 m/km × 1 hr/3600 s)E = 0.937 V. Therefore, the average induced voltage between the tips of the wings of a Boeing 747 flying at 800 km/hr above Los Angeles, CA is 0.937 V.
To know more about Faraday’s law visit
https://brainly.com/question/1640558
#SPJ11
A converging lens with a focal length of 8.00 cm forms an image of a 5.00-mm-tall real object that is to the left of the lens. The image is 1.80 cm tall and erect. Part A Where is the object located? Where is the image located? Is the image real or virtual?
In this scenario, a converging lens with a focal length of 8.00 cm forms an image of a 5.00-mm-tall real object. The image is 1.80 cm tall, erect, and we need to determine the locations of the object and the image, as well as whether the image is real or virtual.
The converging lens forms an image of the object by refracting light rays. In this case, the image formed is 1.80 cm tall and erect, which means it is an upright image.
To determine the location of the object, we can use the lens formula: 1/f = 1/v - 1/u, where f is the focal length of the lens, v is the image distance, and u is the object distance. Rearranging the equation, we can solve for u.
Since the image is real and upright, it is formed on the same side as the object. Therefore, the image distance (v) is positive.
To find the location of the image, we use the magnification formula: magnification (m) = -v/u, where m is the magnification. Since the image is erect, the magnification is positive.
Based on the given information, we can solve for the object distance (u) and image distance (v), which will indicate the locations of the object and image, respectively. The image is real because it is formed on the same side as the object.
Learn more about focal here;
https://brainly.com/question/28039799
#SPJ11
For A with arrow= î + 2ĵ − k, B with arrow = -2î + 2ĵ + 4k, and
C with arrow = 2ĵ − 2k, find C with arrow · (A with arrow − B with
arrow).
The dot product of C with arrow and (A with arrow - B with arrow) is -14.
To find the dot product of two vectors, we multiply their corresponding components and then sum the results. Let's calculate the dot product of C with arrow and (A with arrow - B with arrow):
C with arrow · (A with arrow - B with arrow) = (2ĵ - 2k) · [(î + 2ĵ - k) - (-2î + 2ĵ + 4k)]
Distributing the subtraction inside the parentheses, we have:
C with arrow · (A with arrow - B with arrow) = (2ĵ - 2k) · î + (2ĵ - 2k) · 2ĵ + (2ĵ - 2k) · (-k) - (2ĵ - 2k) · (-2î + 2ĵ + 4k)
Simplifying each term, we get:
(2ĵ - 2k) · î = 0 (since there is no î component in C with arrow)
(2ĵ - 2k) · 2ĵ = 4 (since the dot product of two identical vectors gives the square of their magnitude)
(2ĵ - 2k) · (-k) = 0 (since the dot product of two perpendicular vectors is zero)
(2ĵ - 2k) · (-2î + 2ĵ + 4k) = -28 (by multiplying and summing the corresponding components)
Adding all the results, we obtain:
C with arrow · (A with arrow - B with arrow) = 0 + 4 + 0 - 28 = -14
Therefore, C with arrow · (A with arrow - B with arrow) is equal to -14.
Learn more about Dot product from the given link:
https://brainly.com/question/29097076
#SPJ11
It is 166 cm from your eyes to your toes. You're standing 250 cm in front of a tall mirror.
Part A) How far is it from your eyes to the image of your toes? Express your answer in centimeters.
d=?cm
The distance from your eyes to the image of your toes is 416 cm.
To determine the distance, we can use the properties of reflection in a mirror. The image formed in the mirror appears to be located behind the mirror at the same distance as the object from the mirror.
Given that it is 166 cm from your eyes to your toes, and you are standing 250 cm in front of the mirror, we can calculate the total distance from your eyes to the image of your toes.
The distance from your eyes to the mirror is 250 cm, and the distance from the mirror to the image is also 250 cm, making a total distance of 250 cm + 250 cm = 500 cm.
Since the image is formed at the same distance behind the mirror as the object is in front of the mirror, the distance from the mirror to the image of your toes is 500 cm - 166 cm = 334 cm.
Therefore, the distance from your eyes to the image of your toes is 416 cm.
Learn more about reflection here; brainly.com/question/11684071
#SPJ11
A particle moves along the x axis according to the equation x = 1.97 +2.96t-1.00r2, where x is in meters and t is in seconds. (a) Find the position of the particle at t = 3.10 s. (b) Find its velocity at t = 3.10 s. (e) Find its acceleration at t= 3.10 s.
At t = 3.10 s, the position of the particle is approximately 1.545 meters, the velocity is approximately -3.14 m/s (indicating motion in the negative direction), and the acceleration is -2.00 m/s².
(a) The position of the particle at t = 3.10 s can be found by substituting the value of t into the equation x = 1.97 + 2.96t - 1.00t²:
x = 1.97 + 2.96(3.10) - 1.00(3.10)²
x ≈ 1.97 + 9.176 - 9.601
x ≈ 1.545 meters
(b) The velocity of the particle at t = 3.10 s can be found by taking the derivative of the position equation with respect to time:
v = d/dt (1.97 + 2.96t - 1.00t²)
v = 2.96 - 2.00t
v = 2.96 - 2.00(3.10)
v ≈ -3.14 m/s
(e) The acceleration of the particle at t = 3.10 s can be found by taking the derivative of the velocity equation with respect to time:
a = d/dt (2.96 - 2.00t)
a = -2.00 m/s²
Learn more about Velocity here:
brainly.com/question/30559316
#SPJ11
Two concentric loops of radius r1=1cm and r2-2cm have equal currents in opposite directions. What current will create a magnetic field strength of 350µT at the center?
A current of approximately 559 nA is required to create a magnetic field strength of 350 microteslas (µT) at the center of the concentric loops.
To calculate the current required to create a magnetic field strength at the center of the loops, we can use Ampere's Law, which states that the magnetic field along a closed loop is proportional to the current passing through the loop.
The formula for the magnetic field at the center of a circular loop is given by:
B = (μ₀ × I × N) / (2 × R)
Where: B is the magnetic field strength at the center of the loop,
μ₀ is the permeability of free space (4π × 10⁻⁷ T m/A),
I is the current passing through the loop,
N is the number of turns in the loop, and
R is the radius of the loop.
In this case, we have two concentric loops with radii r1 = 1 cm and r2 = 2 cm, respectively. The current in the loops is equal and opposite, so the net current passing through the center is zero.
Since we want to create a magnetic field strength of 350 µT (350 × 10⁻⁶ T) at the center, we can rearrange the formula to solve for the current:
I = (B × 2 × R) / (μ₀ × N)
Plugging in the values, we get:
I = (350 × 10⁻⁶ T × 2 × 0.015 m) / (4π × 10⁻⁷ T m/A × 1)
Simplifying the expression:
I = (7 × 10⁻⁶) / (4π)
I ≈ 5.59 × 10⁻⁷ A (or 559 nA)
Therefore, a current of approximately 559 nA is required to create a magnetic field strength of 350 µT at the center of the concentric loops.
Read more about Ampere's Law here: https://brainly.com/question/15406320
#SPJ11